Disclosure: As an Amazon Associate, UMT Smart Tool earns from qualifying purchases. This guide is built from product listings and maker specifications, not our own direct testing, so confirm dimensions, drain location and included parts before you order. Listing details are approximate; check the current listing before buying. Installation usually needs a licensed plumber, and drain, venting and waterproofing should be checked against local code. Last updated: November 9, 2026.
The best bathtub fits your room, your floor and the way you bathe. A deep freestanding soaker suits a primary bathroom built around long baths, while a standard alcove tub earns its keep in a shower-and-tub combination used daily. Material matters too: acrylic is light and warm to the touch, while enameled steel and cast iron feel solid but weigh far more. The six choices below cover the main shapes and needs, plus the sizing details that decide whether a tub works.
Quick Choices
| Product | Type | Best for |
|---|---|---|
| Signature Hardware Boyce Freestanding Tub | Freestanding acrylic soaker | Best overall for a primary bathroom |
| Kohler Underscore Alcove Bath | Alcove acrylic soaker | Deep soaking in a standard alcove |
| American Standard Princeton | Alcove enameled steel / Americast | Everyday tub-shower combinations |
| WOODBRIDGE 59-Inch Freestanding Tub | Compact freestanding acrylic | Smaller rooms that still want a soaker |
| Kingston Brass Aqua Eden Clawfoot Tub | Cast iron clawfoot | Traditional and vintage-style bathrooms |
| Empava 59-Inch Freestanding Soaking Tub | Freestanding acrylic, fiberglass reinforced | Value freestanding soaking |
In this guide
Our Choices
Top pick
1. Signature Hardware Boyce Freestanding Tub
The Boyce is a freestanding acrylic soaker from Signature Hardware, sold in a 65-inch nominal length that suits most primary bathrooms without overwhelming them. The shell is formed from two acrylic sheets, and the maker notes the air gap between them acts as insulation, helping bathwater hold its temperature. An built-in drain and overflow keep the exterior clean, with no exposed piping to work around. The bathing well is shaped for reclining rather than sitting upright, and the listed water depth of about 14 inches to the overflow gives genuine shoulder coverage for many bathers. Strengths are the balanced size, tidy built-in hardware and warm acrylic surface. Trade-offs are typical of freestanding tubs: you need clearance on all sides for cleaning, a floor- or wall-mounted filler is a separate purchase, and the drain position must be planned before the floor is finished. It suits homeowners remodeling a primary bath around a dedicated soaker.
2. Kohler Underscore Alcove Bath
The Underscore is Kohler’s answer to a common problem: a standard 60 x 30-inch alcove that still gives a deep soak. Kohler lists a water depth of 15-1/8 inches, deeper than most tubs in this footprint, helped by the slotted overflow design, and a capacity of about 60 gallons. The acrylic body has molded lumbar support, so the backrest is shaped rather than flat, and an integral flange helps waterproof the wall junction. As a three-wall alcove design, it drops into the most common US bathroom layout and pairs naturally with a shower above it. Left- and right-hand drain versions let you match existing plumbing. The main trade-off is that the required Clearflo slotted overflow drain is sold separately, so value for it. The clean, squared lines also suit contemporary remodels better than a curvy builder-grade tub. It suits anyone replacing a worn alcove tub who wants a deeper bath without moving walls or drains.
3. American Standard Princeton Alcove Tub
The Princeton is the practical classic on this list. American Standard builds it from Americast, its engineered steel composite with a porcelain enamel surface, and describes it as a durable alternative to cast iron at roughly half the weight. In its common 60 x 30-inch size it lists a 42-gallon capacity and a soaking depth of about 9-1/2 inches: this is a shower-first tub that also handles a comfortable everyday bath, not a deep soaker. An integral apron front and three-sided tiling flange simplify installation. The enamel surface is glossy, nonporous and easy to wipe down, and many versions add a slip-resistant bottom. Left- and right-drain versions are widely stocked, which helps on tight remodel schedules. Trade-offs follow from the design: the shallow depth will disappoint dedicated soakers, and like any enamel-over-metal tub, a hard dropped object can chip the finish. It suits families and landlords who need a sturdy, familiar tub for a busy tub-shower combination.
4. WOODBRIDGE 59-Inch Freestanding Tub
WOODBRIDGE built its name on freestanding acrylic tubs that undercut showroom brands, and its 59-inch model suits a modest room. Listings for this size give exterior dimensions of about 59 x 29-1/2 inches, a water depth to overflow of about 14-1/2 inches and an effective capacity around 57 gallons, so it soaks deeper than its footprint suggests. The shell is high-gloss LUCITE acrylic reinforced with resin and fiberglass, in a double-wall construction, and many versions include the drain and overflow in a choice of finishes. The oval, double-ended shape lets a bather recline from either end. Trade-offs: taller bathers will bend their knees in a compact footprint, included hardware varies by listing, so confirm what your SKU ships with, and support runs through the seller rather than a local dealer network. It suits smaller primary bathrooms and guest suites that want a freestanding look and a real soak in limited space.
5. Kingston Brass Aqua Eden Clawfoot Tub
For a period bathroom, nothing looks the part like a clawfoot. Kingston Brass sells the Aqua Eden line in acrylic and cast iron; the cast iron double-ended versions, in a 66-inch length, are the traditional article, with enamel over iron, a rolled rim and metal feet, including lion-paw styles. Kingston Brass lists water depth of about 14-3/4 inches for this model, and cast iron’s mass holds heat well. Because the tub stands on feet with plumbing exposed beneath, installation differs from a skirted tub, and many models have no faucet drillings, so plan on a freestanding or wall-mounted filler. The exterior can also be finished to match trim for a more deliberate, finished look. Trade-offs are weight and upkeep: a cast iron clawfoot is very heavy before water and a bather are added, so the floor must be assessed, and the exterior and floor underneath need regular cleaning. It suits owners of older homes designing around a vintage look.
6. Empava 59-Inch Freestanding Soaking Tub
Empava’s 59-inch freestanding soaker is a value-oriented way into the category. The tub is glossy white acrylic reinforced with fiberglass, and listings for the EMPV-59FT1505 version give a capacity of about 53 gallons and a soaking depth of about 16 inches, deep for this length thanks to a tall, compact shape. Drain and overflow are included on many versions, while the filler is excluded, so choose a floor- or wall-mounted filler that reaches over the rim. Its modest weight for its size also makes second-floor placement less demanding than heavier tub types. The straight-sided styling works in modern bathrooms, and acrylic keeps the weight manageable where cast iron would be a problem. Trade-offs: specifications vary across Empava’s many similar model numbers, so verify your exact SKU’s dimension sheet before roughing in the drain, and parts support is less established than the big plumbing brands. It suits value-conscious remodelers who want a deep, modern soaker.
Best by Category
- Best overall: Signature Hardware Boyce, for its balanced size, double-sheet construction and built-in drain.
- Best alcove soaker: Kohler Underscore, the deepest soak here in a standard 60-inch alcove.
- Best for tub-shower combos: American Standard Princeton, a durable Americast workhorse for daily use.
- Best compact freestanding: WOODBRIDGE 59-inch, with genuine soaking depth in a smaller footprint.
- Best traditional: Kingston Brass Aqua Eden cast iron clawfoot, for heat-holding mass and period looks.
- Best value freestanding: Empava 59-inch, a deep acrylic soaker, if you verify the exact model’s specification sheet.
How to Choose
Tub types: freestanding, alcove, drop-in, corner and walk-in
An alcove tub fits between three walls and is the standard for tub-shower combinations. A freestanding tub stands away from the walls and needs room around it plus a floor- or wall-mounted filler. A drop-in tub sets into a framed deck that hides plumbing and creates a ledge. Corner tubs fill an awkward corner and often seat two, at the cost of footprint and water volume. Walk-in tubs, with door and seat, need specialist installation.
Materials: acrylic, cast iron, fiberglass and solid surface
Acrylic is most common: lightweight, warm to the touch, repairable for minor scratches and available in every shape, though it can flex if poorly supported. Cast iron with enamel is heaviest and most durable and holds heat well, but stresses floors and installers. Gelcoat fiberglass is light and usually least expensive, with a thinner feel. Solid surface tubs feel dense and matte and can often be spot-repaired, at higher cost than acrylic. Enameled steel and composites like Americast sit in between.
Size, water depth and floor loading
Measure the space, doorway and the route in; a one-piece tub that cannot pass the stairs is a costly mistake. Then look past exterior length to the bathing well and water depth to the overflow, which decide whether you can stretch out and submerge your shoulders. Finally, do the load math: a filled tub plus a bather concentrates a large load on a small area. Older floors and cast iron deserve a professional joist check first.
Drain and faucet placement
The drain position, end, center or offset, must line up with the waste pipe, or the pipe must move, a decision with cost attached. Alcove tubs come in left- and right-drain versions for this reason. Freestanding and clawfoot tubs usually need a floor-mounted filler, or a wall-mounted one with enough reach; only some accept deck-mounted faucets. Decide the filler early, and confirm whether the drain assembly is included, as it is not on the Kohler above.
Installation and plumbing
Value for the work around the tub, not just the tub. A like-for-like alcove replacement is simplest. Moving a drain or converting to freestanding means opening floors and walls, new waterproofing and often a permit. Tubs must sit level and fully supported, many makers specify a mortar bed, and a plumber should confirm the rough-in against the specification sheet before tile closes in.
Cleaning and durability
Acrylic and solid surface clean with mild, non-abrasive products; abrasive pads can dull or scratch them. Enamel over iron or steel tolerates more but can chip if struck, and chips should be repaired before rust begins. Fiberglass gelcoat needs gentler handling. Whatever the material, ventilate the room and check caulk yearly. Longevity comes less from the badge than from correct support and sensible cleaning.
Planning Around Your Bathroom Layout and Access
A tub has to physically reach its room before it can be installed. Many projects stall because the tub that looked right on a listing could not pass through a doorway, turn a stair landing or fit beside an existing wall.
Measure the route
Measure doorways, hallway turns and stairwells, and compare them with the packaged dimensions in the listing, not only the finished tub size. Large one-piece tubs may need a wide path and more than one person to carry.
Check the room
Consider clearance around the tub for cleaning, space for a faucet and a spot to rest a towel. In small bathrooms, an alcove model against three walls usually fits more easily than a freestanding design that needs open space on every side.
Think about getting in and out
Rim height and tub depth change how easy it is to step over. Households with children or older adults may want a lower side, a grab bar installed according to a professional’s advice, or a non-slip surface.
Shape, Slope and Soaking Comfort
Two tubs with the same length can feel very different once you are inside. The inner shape, the angle of the back and the position of the overflow decide how comfortable a long soak is.
- Sloped back: lets you recline rather than sit upright, and a double-slipper style lifts both ends.
- Overflow position: a low overflow limits water depth, while a higher one allows deeper filling.
- Interior length: measure the inside bottom, since the outer rim size can be misleading.
- Wall thickness: thicker rims look substantial but reduce the usable inner space.
If you can, compare the inner dimensions across listings and sit in a similar tub in a showroom. A photo rarely shows how the back angle feels in practice.
Finishes, Trim and Drain Kits
Some tubs arrive as a bare shell, while others include trim, overflow and drain parts. Missing hardware is a frequent surprise, so read the listing carefully before you place an order.
| Part | Often included? | What to check |
|---|---|---|
| Drain and overflow kit | Sometimes | Finish and compatibility with your plumbing |
| Faucet | Rarely | Deck, wall or floor mount, and hole count |
| Feet or pedestal | Varies | Height and adjustability |
| Tub surround | No | Material and sealing method |
Choose finishes that match your faucet and other bathroom fixtures. Chrome, brushed nickel and matte black each age differently, so check the care guidance for the one you choose.
Common Bathtub Buying Mistakes
A tub is a big purchase with limited room for error, and a few mistakes show up again and again.
- Ordering before confirming the drain position matches the plumbing in the floor.
- Forgetting that a filled tub, water and a person add substantial weight, and not checking the floor structure with a licensed professional.
- Assuming a freestanding tub drops in where an alcove tub used to be.
- Skipping the delivery check, then discovering damage after the packaging has been thrown away.
- Overlooking the water heater capacity for a deep soaking tub.
Any plumbing, drain or structural work should follow the manufacturer’s instructions and the advice of a licensed plumber or contractor, especially in older homes.
More Bathtubs Worth a Look
Kohler Archer Alcove Bath
The Archer is a traditional alcove bath with a slightly rolled rim and a clean, familiar shape. It suits renovations that replace a standard three-wall tub in place. Check the listing for the drain side, dimensions and material, and confirm whether the tub is sold with or without drain hardware before ordering.
Delta Classic 400 Alcove Bathtub
Delta’s Classic 400 is a straightforward alcove tub intended for standard bathrooms with a three-wall recess. It is aimed at renovators who want a dependable shape without decorative extras. Read the listing for the available drain positions, material and size, and ask a plumber about compatibility with your existing rough-in.
Vanity Art 59 Inch Acrylic Freestanding Bathtub
This compact freestanding tub suits smaller bathrooms where a full-sized soaker would crowd the room. Acrylic is lightweight and warms quickly. Check the listing for the interior length, overflow style, included hardware and faucet requirements, and measure the delivery path before ordering.
Vinnova Freestanding Acrylic Bathtub
Vinnova offers freestanding acrylic tubs in several sizes and shapes, a typical choice for people who want a focal point in a larger bathroom. Read the listing for the dimensions, the overflow and drain details and the finish options. A freestanding tub also needs a suitable faucet, so plan that part of the project early.
More Questions Buyers Ask
How much clearance do I need around a freestanding tub?
Leave enough room to clean on every side and to walk around comfortably. Many installers suggest several inches at minimum, but the manufacturer’s installation guide and local building rules decide the exact figures.
Can I install a tub myself?
Some people handle simple replacements, but plumbing connections, floor support and sealing affect safety and water damage risk. Follow the maker’s instructions and consider hiring a licensed plumber for the drain, supply and structural parts.
Why does a tub need a flat, supported floor?
A filled tub is heavy, and an uneven base can stress the shell and the drain connection. Manufacturers often specify the type of support or a mortar bed, so read the installation guide before delivery.
What should I check when the tub arrives?
Inspect the surface for chips, cracks and scratches before signing for it, and photograph any damage. Keep the packaging until you have confirmed that the tub and all included parts are in good condition.
Frequently Asked Questions
What size bathtub should I buy?
Match the tub to the space first, then to the tallest bather. A standard alcove is 60 inches long. Taller bathers need a longer tub, or a deeper one with a shaped backrest, so compare well dimensions and water depth, not exterior size.
Is acrylic or cast iron better?
Neither is simply better. Cast iron is exceptionally durable and holds heat well but is very heavy and costs more to install. Acrylic is far lighter, warm to the touch and comes in more shapes, but needs full support and gentle cleaning. Your floor and value decide.
Can I replace an alcove tub with a freestanding tub?
Often, yes, but it is a remodel, not a swap. The drain usually moves, filler lines must be run, walls behind the old alcove need finishing, and the new tub needs clearance on all sides.
How much water does a bathtub use?
It varies with tub size and fill level. Makers list capacities per model: here they range from about 42 gallons for the Princeton to around 60 gallons for the deeper soakers.
Do I need a plumber to install a bathtub?
In most cases, yes. Drain, overflow, vent and supply connections must be watertight and code-compliant, and errors hide inside floors and walls until they cause damage. Local rules may require a permit.
How long should a bathtub last?
A well-installed tub should serve for many years. Cast iron and quality acrylic generally outlast thin gelcoat fiberglass, but installation quality and cleaning habits matter as much as material.
Bottom Line
Choose the shape that fits your room and routine first, then compare water depth and material. The Boyce is the balanced freestanding choice; in an alcove, the Underscore soaks deepest and the Princeton covers daily family use; WOODBRIDGE and Empava bring freestanding soaking to smaller rooms and needs, and the Aqua Eden serves traditional bathrooms. Whatever you choose, verify the specification sheet, drain position and floor capacity with your plumber before ordering.







