A combination square has a sliding head on a ruler blade, and it does several jobs: marking lines square to an edge, marking 45 degree lines, measuring depth, and gauging parallel lines. Slide the head to the setting you need, lock it, and keep the head tight to the work.
Parts of the Tool
- Blade: The graduated ruler that slides in the head.
- Head (stock): The body that rides against the work and has a 90 degree and a 45 degree face.
- Locking knob: Holds the blade at the chosen position.
- Level vial and scribe: Included on some models. Follow the maker’s guide if yours has them.
In this guide
Setting and Locking the Blade
- Loosen the locking knob and slide the blade to the measurement you want.
- Read the mark where the blade passes the head’s face, and confirm it twice.
- Tighten the knob firmly, but do not overdo it.
- Check that the blade has not shifted before you mark.
Using It Step by Step
Marking a square line
Press the head tight against a straight board edge, with the blade lying flat on the surface. Draw along the blade with a sharp pencil.
Marking a 45 degree line
Use the angled face of the head against the board edge and draw along the blade. This helps lay out miters and bevels.
Marking a parallel line
Set the blade to the distance from the edge. Hold the pencil at the end of the blade, slide the head along the edge, and the pencil traces a line parallel to it. Keep downward pressure steady.

Checking depth
Set the head across the top of a hole or groove, lower the blade until it touches the bottom, lock it, and read the depth.
| Job | Head face used | Watch for |
|---|---|---|
| Square line | 90 degree face | Dust under the head |
| Miter line | 45 degree face | Check against scrap |
| Parallel line | Head slides on the edge | Steady pencil pressure |
| Depth | Head across the opening | Blade fully seated |
Checking Accuracy
Draw a line along the blade against a straight edge, flip the square over, and draw again. If the lines do not match, the head or blade is off. Keep the surfaces clean and avoid dropping the tool. The maker’s guide may describe how to adjust it if needed.
What to Look For When Choosing One
Combination squares vary in construction, and a few features decide how useful one will be. Start with the blade. It should be straight, with clear graduations that are easy to read and that run in the units you work in. Some blades carry both imperial and metric scales, while others carry a single system, so check the listing for what is engraved and in what increments.
Next look at the head, which should sit flat, slide smoothly and lock without wobble. A head that rocks on the blade will give poor results regardless of the blade quality. Heads made of cast metal are common and sturdy, though check the product description for details of the finish and the lock mechanism. Some heads include a small spirit vial and a scribe, which are handy extras but not essential.
Consider the blade length too. A shorter one is easier to carry and handles most small bench tasks, while a longer blade reaches farther across wide boards. Choose by the jobs you do most.
- Check that the blade slides without sticking or rattling.
- Confirm the locking knob grips firmly and releases easily.
- Look for a head face that is flat, clean and free of burrs.
- Make sure the markings are legible in your normal lighting.
Budget tiers differ mainly in finish, fit and how well the parts hold their accuracy over time. Read the manual or product page to understand what the maker claims, and test the square against a known straight edge when it arrives.
Testing and Correcting Squareness in Detail
The flip test described above is the standard check, but it helps to do it carefully. Choose a board with a truly straight edge, ideally one you have checked yourself. Press the head against the edge, draw a fine line along the blade with a sharp pencil or marking knife, then flip the square over without moving the board and draw again from the same point. If the two lines coincide, the square is true. If they form a narrow wedge, the angle between the head and blade is off, and the gap shows twice the error.
Also check the blade itself. Lay it against a straight reference to see whether it bows. Check that the head’s 45 degree face behaves consistently by testing it against a known miter or by drawing lines from both directions.
If the square is off, do not use it for precise work until it is resolved. Some makers describe an adjustment procedure, and others consider it a fixed tool that should be replaced. Follow the manual rather than filing or bending parts.
- Clean the head face and blade before each test, since dust can create false errors.
- Test again after any drop or hard knock.
- Keep a separate reference square, if you have one, for comparison.
A small test now and then costs seconds and prevents hours of misaligned parts.
Marking Methods and Pencil Technique
A square is only as precise as the line you draw with it. A thick pencil line can be a good part of a millimeter wide, which throws away much of the square’s accuracy. Use a sharp pencil, hold it at a consistent angle and keep it tight against the blade. For finer work, a marking knife or a scribe leaves a thin cut line that also gives a saw or chisel a starting groove.
Decide which side of the line you cut on, and mark the waste side with a small cross. A line has width, so the cut should remove the line or leave it consistently, depending on the plan. When you mark several parts to the same length, set the square once and transfer from the same reference edge to avoid cumulative errors.
Always reference from the same face and edge. Mark one face and one edge of the board as your datum, and measure and square everything from those. Mixed references introduce errors, especially if edges are not perfectly parallel.
- Press the head firmly against the edge while drawing, not just touching it.
- Draw toward the head rather than away, to keep pressure holding it in place.
- Check that the blade sits flat on the surface and does not lift at the far end.
Good technique matters more than the price of the tool for most projects.
Beyond the Basics: Other Jobs for the Tool
Once you are comfortable with square, 45 degree and depth marking, a combination square can handle other small tasks. Used as a straight edge, the blade can guide a knife or a pencil for a short line. Set to a fixed distance, it can check the position of a hole or a mortise relative to an edge, and then double as a quick comparison between identical parts.
It can check that a machine setting is close to square, such as a saw blade against a table, though dedicated setup tools may be better for fine adjustments. Check the saw manual for the preferred method. The 90 degree face can help you assess whether a joint is square by sitting it inside a corner. On a workbench, it can confirm that a vise jaw or a stop is true to the surface.
Be sensible about limits. A combination square is a marking and checking tool, not a hammer, a pry bar or a scraper. Using it for those jobs can damage the blade edge or the head faces and ruin its accuracy.
- Use it to compare matching parts, holding each against the same setting.
- Use the depth feature to check consistent rebates or holes across several pieces.
- Avoid using the blade as a scraper or screwdriver.
Care, Storage and When to Replace
A combination square lasts for years if you treat it as a measuring instrument. Wipe the blade and head after use to remove dust, sweat and finish residue. A light coat of a rust-preventing product, as the maker suggests, helps in damp workshops. Keep oil away from the faces that touch your work, since residue can transfer to wood and affect finishes.
Store it where it will not be crushed or bent, ideally hanging on a hook or lying in a drawer compartment on its own. Do not toss it loose in a box with heavy tools. Loosen the locking knob slightly for long storage if the maker recommends it, to avoid sticking.
Signs that it is time to repair or replace the square include a head that no longer passes the flip test, a bent blade, worn or illegible markings, a lock that slips and a head with chipped or burred faces. Minor surface rust can sometimes be cleaned gently, but pitting on the working edges or scale can reduce accuracy.
- Check the square against a known reference every so often.
- Replace it when accuracy cannot be restored.
- Keep the original manual for any adjustment or care notes, and note the date you last checked accuracy.
Reading the Scale Without Mistakes
Many layout errors are reading errors, not tool errors. Combination square blades commonly carry more than one scale, and the marks are fine enough to misread when you are in a hurry.
- Inch blades are often graduated in eighths, sixteenths, thirty-seconds and sixty-fourths on different edges. Pick one edge and use it for the whole job so your readings stay consistent.
- Metric blades show millimeters, usually with longer marks at every five and ten. Count from the nearest numbered mark instead of counting every line.
- Always read the scale at the point where the blade passes the head face, not at the end of the blade.
- View the scale straight on. Looking from an angle shifts the apparent position of the mark, a problem called parallax.
- For repeat settings, write the number down before you lock the knob so you are not relying on memory.
If you work from a plan in fractions, convert everything to the same denominator before you start. Converting once at the top of the page is quicker than converting at the bench, and it reduces the chance of a transposition mistake.
Worked Layout: Marking Shelf Dadoes on a Side Panel
Imagine a small bookcase with two side panels, each needing three shelf dadoes at equal spacing. The combination square can handle all the layout without a separate marking gauge.
Begin by deciding the distance of the first dado from the bottom edge and the spacing between dadoes. Set the blade to the first distance and lock the knob. Hold the head against the bottom edge of the panel and slide the whole tool along the edge, marking a short line at each end of the panel to establish its position. Then use the square line technique to connect the marks, drawing across the face where the dado will start.
For the next dado, loosen the knob, add the spacing to the blade setting, lock it and repeat. Mark both side panels together if they are clamped back to back, so that the layouts match exactly. Pay attention to which faces are the inside faces. Mark an X or a small arrow on the waste side of each line so you do not cut the wrong side of the mark.
Finally, check the layout by laying one panel on top of the other, edges aligned, and viewing the lines together. If any line drifts, find the cause now rather than after the cut. The same method works for other repeated layouts such as shelf pin rows, drawer parts and stair stringer notches.
Setting Machine Heights and Fence Distances
A combination square makes a quick setup gauge at the saw, router table or drill press. The blade can act as a stop of known length, so you can check a setting without needing a separate measuring tool.
- Blade or bit height. Stand the square on its head next to a router bit or saw blade, extend the blade to the desired height, and compare. This is a reference check, not a precision instrument, so confirm the result with a test cut.
- Fence distance. Lock the blade at the required measurement and use the end of the blade to set the distance from fence to blade, or fence to bit, noting that blade or bit width and kerf change the result.
- Drill depth. Set the blade to the intended depth and compare it with the bit or the depth stop on a drill press.
- Squareness of fences and tables. Hold the head against the table and check the blade against the fence for a rough square check before more precise tuning.
Safety matters here. Always switch off and unplug the machine, or remove the battery, before placing a tool near a blade or bit, and wait until all rotation has stopped. Keep hands out of the cutting path, and follow the manual for your machine and local safety rules.
Common Setup Errors and Quick Fixes
- The blade creeps while marking. The knob may be loose, worn or dirty. Clean the blade and the slot, and tighten the knob firmly. If it still slips, consider replacing the tool.
- The head rocks on the work. Check for debris, burrs or a bowed board edge. Run a finger along the edge and file or plane high spots away.
- Lines are not square even when the tool checks out. The reference edge may not be straight. Joint or plane it first, or choose a better edge.
- Measurements are off by a small constant amount. The blade end may be worn or damaged. Use a different starting mark, such as the one-inch line, and subtract.
- The marked line is too thick to cut to. Use a sharp pencil or a marking knife for fine joinery, and mark the waste side so the cut leaves the line.
When something goes wrong, change one thing at a time. Check the tool, then the work, then your technique. Most problems come from a dirty slot, a damaged edge or a rushed reading.
Matching the Tool to Your Skill Level
Beginners tend to get the best results from a simple, well-made combination square used for a few jobs: square lines, 45 degree lines and depth checks. Resist the urge to use every feature at once. Practice first on scrap, comparing your layout with a second measurement, and gradually add tasks such as setting machine heights and repeat layout.
As confidence builds, introduce habits that raise accuracy: marking with a knife, working from one consistent reference face, and checking your work with a second tool. Intermediate users often add a second square of a different size, since a short blade is easier to control on small parts and a long blade covers wide panels. Whatever your level, accuracy comes more from steady technique and a good reference edge than from a more expensive tool.
Using the Square with Other Layout Tools
A combination square works best as part of a small set. Pair it with a marking knife for clean lines, a steel rule for long measurements and a straightedge for lines longer than the blade. A try square or speed square can speed up repeated 90 degree marks on framing lumber, while the combination square excels where adjustable distances matter. For large panels, a framing square or a long straightedge gives better reach than the blade alone.
When you combine tools, keep one reference face and one reference edge for each part, and mark them clearly. Switching reference faces mid-project is one of the most common sources of accumulated error, and a simple pencil mark prevents it.
Practice Exercises That Build Accuracy
Accuracy with a combination square comes from repetition. Try a few simple exercises on scrap lumber. Draw ten parallel lines at one-inch spacing and check them with a ruler. Mark a square line across a board, cut to it, and test the cut end against the square. Mark and cut a 45 degree line on two pieces and join them to see whether they form a clean right angle. Each exercise shows you the size of your own error, which is the first step to reducing it. Keep the results so you can compare after a few weeks of practice.
Ready to Buy? Start Here
If this guide helped you decide what to look for, these products are a place to start.
As an Amazon Associate we earn from qualifying purchases. Prices and availability are shown on Amazon.
First, Check the Square Itself
Every measurement a combination square makes depends on one assumption: that the head sits truly at a right angle to the blade. Tools get dropped, bought cheaply, or knocked out of truth in a toolbox, so verifying the tool comes before trusting the tool. The test below takes two minutes and should be repeated whenever the square is dropped or its readings start to disagree with reality.
The draw, flip and compare test
Place the head firmly against a known straight edge — the factory edge of a sheet of plywood or board serves well — with the blade lying flat on the surface. Draw a fine line along the blade. Then flip the square over, place the head against the same edge at the same spot, and draw a second line beside the first, beginning at the same point. If the square is true, the two lines coincide or run perfectly parallel. If they form a narrow V, the square is out by half the angle of that V — the test doubles the error so you can see it. A square that fails noticeably should be corrected if its design allows adjustment, reserved for rough work, or replaced; fine layout built on a false square is fiction.
Checking the blade and the lock
While you are testing, sight along the blade for bends, check that the scale is legible, and confirm the locking knob holds the blade without creep. Set the blade to a measurement, lock it, then try to slide it with firm thumb pressure. Any movement means settings will drift mid-job, which produces the maddening errors that look like carelessness but are really hardware. Also confirm the head’s faces are clean and free of burrs; a speck of grit trapped between head and reference edge tilts every line you draw.
The Core Measurements, Done Carefully
Marking a line at a set distance from an edge
Set and lock the blade so the exposed length equals your distance. Hook the head over the reference edge, hold a sharp pencil against the end of the blade, and slide the square along the edge, keeping the head pressed firmly to the edge the whole way. The pencil traces a line parallel to the edge at exactly the set distance. The skill is in the pressure: steady inward pressure on the head, light pressure on the pencil, and a speed slow enough that the head never rocks or lifts.
Checking whether an edge or end is square
Rest the head flat against the face of the board and the blade across the edge or end you are testing. Look for light showing under the blade. Light at one end means that end stands high; light in the middle means the surface crowns. Check at several positions along the piece, because an end can be square at one corner and off at the other. Mark the high spots in pencil and correct only those, rechecking as you go.
Measuring and transferring depth
Stand the blade’s end on the reference surface and slide the head down until it meets the rim or shoulder, then read or transfer the exposed blade length. This is the square’s neatest trick for setting and checking depths of grooves, recesses and holes. Lock the setting and you can carry that depth around the whole job, checking every matching feature against one unchanging standard instead of re-measuring each time.
Finding the center of a board or a round piece
With the head set so its two faces form a cradle, a round piece nests against both faces and the blade’s edge points through its center; mark along the blade, rotate the piece, mark again, and the crossing lines reveal the center. For a board’s width, the same cradling idea with the angled face lets you scribe a true center line down its length. These are slow, certain methods — exactly what you want when a center must be right the first time.
Setting a consistent height or fence distance
Stand the square on its head with the blade vertical, set to the height you need, and use it as a small gauge to set a blade, bit or fence, or to check that a setting survived moving the machine. Consistency across a batch comes from one locked setting used repeatedly, not from measuring each piece fresh and accumulating small differences.
Troubleshooting by Symptom
Lines drawn from opposite faces do not meet
When a line carried around a board fails to meet itself, either the square is out of truth or the board’s faces are not parallel, so the reference changed as you moved. Run the flip test on the square first. If the square passes, measure the board’s thickness at both ends; layout can only be as consistent as the stock it references.
The setting changes between measuring and marking
That is lock creep or a head that rocks on a dirty reference. Clean the blade’s slot and the reference edge, lock firmly, and re-check the setting against a rule after locking, because some squares shift a fraction as the knob tightens. Knowing your own tool’s tightening shift, and compensating for it, is part of using it well.
Pencil lines come out thick or doubled
A blunt pencil wandering along the blade’s edge is the usual cause. Keep the pencil sharp, hold it at a consistent slight angle against the blade, and draw in one pass. For the finest work, a marking knife against the blade gives a line with no width at all and a tiny groove that guides the next tool.
Readings disagree with your tape measure
One of the two tools is being misread, or their zero points differ. Compare them directly along the same span, confirm you are reading the same scale system on both, and remember that a square’s blade is read where it exits the head, not from its end. Most disagreements end at a misread scale rather than a faulty tool.
Common Mistakes and Their Fixes
Letting the head rock is the most common error: the head must sit fully against the reference for the entire stroke, and any tilt prints directly into the line. The second is trusting a square that has never been tested; two minutes with the flip test settles the question permanently. The third is reading the scale from an angle, which shifts the apparent position — read square-on, at eye level with the mark. The fourth is using the tool as a scraper, pry or hammer substitute, which bends blades and burrs heads. The fifth is storing it loose in a toolbox where the blade takes knocks; a pouch, a slot in a drawer or a magnetic strip keeps the tool true between jobs.
Results Checklist
Before layout begins, confirm the following. The square passed the flip test recently, and its blade is straight, clean and legible. The lock holds a setting against firm thumb pressure, and you know whether your tool shifts as it tightens. The reference edge for the job is itself straight and clean. Your pencil is sharp, or your knife is ready for fine lines. During the work, every setting is rechecked after locking, and critical lines are verified from a second reference when the fit matters. When the list holds, the lines the square produces deserve your trust — and trust, verified rather than assumed, is what layout tools are for.
More Questions, Answered in Depth
How often should the flip test be repeated?
After any drop, after lending the tool, and whenever two layout methods disagree on the same piece. In a calm home workshop that may mean a few times a year. The test is cheap; the cost of a false square compounds through every cut a project makes from its lines.
Can one square serve for both rough and fine work?
Yes, provided it passes the flip test and locks firmly. Reserve your care for it accordingly: a square trusted for joinery layout should not be the one thrown into a site bag for rough framing checks. Many careful workers keep the verified square in the bench drawer and let an older tool travel.
What is the best habit for reading the blade quickly without errors?
Read in two passes. First read the large divisions to place yourself, then the fine division for the exact figure, then say the number aloud or write it on the workpiece immediately. Most scale errors are memory errors wearing a disguise: the reading was right, and the number changed during the walk to the saw.
Worked Examples: The Square on Real Layouts
Example one: laying out evenly spaced shelf supports
A bookcase side needs a column of support holes or notches at even spacing. Set the square once for the spacing from the front edge and strike that line down the side; then work along it, stepping the square’s locked setting from mark to mark only if the design measures spacing relatively — or better, reference every position from the same end with the blade, so errors cannot accumulate. The example teaches the square’s deepest lesson: one locked setting, used repeatedly from one reference, beats a dozen fresh measurements.
Example two: checking a drawer box before glue
Before glue, each corner of the drawer box gets the square’s verdict: head on one side, blade across the other, light check at top and bottom of the joint. A corner can pass at the top and fail at the bottom if a side twists, and the square finds it in seconds while correction is still free. Diagonal measurements across the assembled box complete the check — equal diagonals plus square corners is certainty; either alone can deceive.
Example three: setting a consistent reveal around a door or panel
A reveal — the even margin around a fitted door — is a locked setting made visible. Set the square to the reveal width and run it around the opening, marking the line the door’s edge must meet. Fitting then becomes shaving to a line rather than guessing at evenness by eye. The same trick serves picture frames, inset lids and any place where the eye judges evenness more harshly than any single dimension.
Pairing the Square With Honest References
The square transfers truth; it cannot create it. Its results are only as good as the edge its head rides on, so part of using it well is curating references: one board edge jointed or factory-cut and reserved as your layout reference, sheet goods whose factory edges you have verified, and machine fences checked against the square rather than assumed. When two references disagree, believe the flip test and the string test over habit. A small kit of verified references — the tested square, a known-straight edge, a reliable tape — is the foundation every accurate project quietly stands on, and building that kit once pays out on every layout afterward.
Care Habits That Keep the Tool True
Truth leaves a tool through small insults: the drop onto concrete, the winter in a damp toolbox, the blade used to scrape paint. Build the counter-habits. Wipe the blade clean after use, especially after contact with glue or moisture. Store the square flat or hanging, never loose under heavier tools. Ease the lock off for long storage so the mechanism rests. Re-run the flip test at the start of any project where fit truly matters, the way a musician checks tuning before the performance rather than after it. None of this takes more than a minute, and all of it protects the single property that makes the tool valuable — the fact that its angle can be believed.
Angles Beyond Ninety and Forty-Five
The combination square’s two famous angles get the attention, but its blade-and-head geometry supports more. With the head slid and locked at a chosen point, the square becomes a repeatable marking gauge for any layout that repeats a distance, whatever the angle of the work. For angled layout, the square’s role is usually partnership: another tool establishes the angle, and the square transfers it consistently — marking the same offset from a reference edge at both ends of an angled line, checking that repeated angled parts match the first, and carrying a setting from a sample piece to its copies without re-measuring. Repetition, not novelty, is where the square earns its place in angled work: angles are easy to strike once and surprisingly hard to strike identically ten times without a locked reference.
A Short Daily-Use Routine for Accuracy
Accuracy with the square is a routine, not a talent. Pick the tool up and glance along the blade for damage. Set the dimension, lock, and re-read the setting after locking. Seat the head with full contact and confirm it by feel before the pencil moves. Draw once, in one direction, with the pencil held consistently against the blade. Verify the first line of any batch against an independent measurement, then trust the locked setting for the batch while spot-checking occasionally. Put the tool down in its home, never on the workpiece where the next board will land on it. Run this loop until it is automatic, and your layout errors will shrink to the honest remainder that checking catches — which is all any craftsperson, in any century, has ever managed.
From Single Lines to Whole Layouts
The square’s final promotion is from marking single lines to governing whole layouts. In a full layout, one reference face and one reference edge — chosen, marked and never changed mid-project — feed every measurement the piece receives, and the square is the tool that carries dimensions from those references to every face. Parts laid out this way agree with each other even when individual dimensions drift slightly from the plan, because shared references create shared truth. Mark the reference faces with a clear symbol the moment stock is prepared, before any other mark competes for the surface, and let every later operation ask the same question: which face governs this measurement. Projects fail in layout far more often than in cutting, and they fail by accumulation — small reference changes compounding invisibly until assembly exposes them. The square, verified by its flip test and used from unchanging references, is how careful makers make accumulation work for them instead of against them: every line reinforcing the same geometry, from the first knife mark to the last checked corner.
The Square as a Teacher
Stay with this tool long enough and it begins teaching lessons larger than layout. It teaches that accuracy is verified, never assumed — a two-minute flip test standing in for a whole philosophy of work. It teaches that consistency beats brilliance: one locked setting, faithfully repeated, outperforms inspired measurement after inspired measurement. And it teaches that small errors compound in silence, so the time to catch them is at the line, where they cost an eraser, rather than at assembly, where they cost the project. Makers who internalize those lessons find them applying everywhere — in measuring twice without resentment, in testing joints before glue, in checking the first of anything before producing the rest. The combination square is a modest tool, a head and a blade and a knob. Used with the discipline this guide describes, it becomes the standard against which a whole workshop’s honesty is measured, one true line at a time.
FAQ
Is a combination square better than a speed square?
They suit different tasks. A combination square excels at adjustable settings and depth checks, while a speed square is handy for fast, large layouts.
Why does my line change when I tighten the knob?
The blade may shift as it locks. Hold it against the head while tightening and recheck.
How long should the blade be?
Choose based on the jobs you do. A shorter blade suits small bench work and fits in a pocket or apron, while a longer one reaches across wider boards. Check the listing for the exact length.
Can I use a combination square for metalwork?
It can be used for layout on many materials, but marking methods differ, for example a scriber instead of a pencil on metal. Follow the maker's guidance on what the tool is designed for.
Why do my lines look doubled after flipping the square?
Either the square is slightly out of true or the board edge is not straight. Test on a different, verified edge, and compare against another square if you have one.
What is the scribe for?
Some heads hold a small pointed scribe used to scratch fine lines on materials such as metal. Check whether your model includes one and how the maker says to use it.
Is a combination square accurate enough for fine joinery?
It can be if it is a well-made, properly tested example and used with good technique. For very fine work, many people also keep a dedicated solid square for checking.
How do I read the blade quickly?
Learn the main divisions of your scale first, then count the smaller ticks from the nearest mark. Double-check each reading before you lock the head.
Should I buy the version with a level vial?
It is optional. The vial can be convenient for rough checks, but it is not a substitute for a proper level when plumb or level matters.
How do I check if my combination square is square?
Draw a line along the blade against a straight board edge, flip the square over to the other side of the line and see whether the blade lines up with the first mark. A visible gap means the head is out of square. Test on a board with a truly straight edge.
Can I use a combination square to find the center of a board?
Not directly for width, but you can set the blade to a half-width measurement and mark from both edges, then adjust until the marks meet. For round stock, a dedicated center head attachment is usually easier. Use light pencil marks and check them twice.
What is the best way to clean a combination square?
Wipe the blade and head with a dry cloth, remove sawdust from the slot with a soft brush, and apply a light coat of machine oil or paste wax to prevent rust, following any maker guidance. Avoid abrasives that could scratch the graduations.
Should I buy an inch or metric combination square?
Choose the scale you use for most projects. Many blades carry both inch and metric edges, which can help if your plans mix units. Check that the graduations are clear and the blade is easy to read in your workshop lighting.
How tight should the locking knob be?
Tight enough that the blade does not move when you press the head against the work, but not so tight that you strain the thread or bend the blade. Hand tight is usually sufficient. If it slips at that setting, clean the slot and check for wear.
The Short Version
Slide and lock the blade, hold the head tight to a straight edge, and mark with a sharp pencil. Use the 45 degree face for angles, and check the square for accuracy now and then. Follow the maker’s guidance.



