Sandpaper grit is a number: the lower it is, the coarser the paper and the faster it removes material. Higher numbers cut less and leave a smoother surface. Keep this cheat sheet nearby and treat the ranges as rough guides, since makers label products a little differently.
Grit Quick Reference
| Grit range | Label | General use |
|---|---|---|
| 40 to 60 | Coarse | Heavy removal, shaping, rough boards |
| 80 to 120 | Medium | Leveling, removing marks from coarse grit |
| 150 to 220 | Fine | Smoothing before a coating or stain |
| 320 to 400 | Very fine | Light sanding between coats |
| 600 and above | Extra fine | Polishing and delicate finishing |
In this guide
The Basic Order
- Choose the lowest grit that removes the flaw without being rougher than needed.
- Sand until the surface looks uniform.
- Move to the next grit in the list and repeat.
- Wipe away dust before each change.
- Finish at the grit suited to your coating, as its label directs.
Handy Rules
- Skipping more than one step in the sequence can leave scratches that stay visible.
- Sand along the grain on wood.
- Let the paper do the work, with light pressure.
- Replace worn paper, since clogged sheets burnish instead of cutting.
Materials Differ
Bare wood, metal, plastic, and old coatings each respond differently. Softwoods can scratch easily, while hard surfaces need finer grits for a polished look. Wet-or-dry sheets suit certain jobs when the label allows water.
Dust and Care
Fine dust can irritate lungs and eyes. Wear a dust mask and eye protection, work with ventilation, and follow local guidance about sanding old coatings, which may contain hazardous substances. If you use a power sander, read its manual.
Grit is only part of the picture. Sandpaper also comes with different abrasive materials and backings, and the label usually lists what the sheet is meant for. Some sheets suit bare wood, others suit metal or between-coat work. Sheets, discs, belts, and sponges all use the same grit idea, so the cheat sheet applies to each. Sponges flex around curves, while discs fit a power sander. Check the packaging, and match the paper to both the surface and the sanding tool.
Different grit systems exist. Some makers label paper with a P before the number, while others use plain numbers, and the two scales are close but not identical at the fine end. When mixing brands or sheet types, compare the printed numbers carefully and keep the same system for the whole job. Store sheets flat in a folder so they do not curl or crack.
Grit Choices for Common Jobs
A table of ranges tells you what the numbers mean, but most people want to know what to pick for a particular job. These are general starting points, not rules, and the product label of any finish, filler or abrasive should take priority.
For removing old paint or varnish, a coarse to medium grit gets the bulk of the coating off, but it leaves scratches that must be removed with finer grits afterward. Chemical strippers or scrapers are sometimes a better first step, particularly on detailed surfaces. Check the age of the coating first, because old paint can contain hazardous substances.
For preparing bare wood for stain or clear finish, work from a medium grit to a fine one and stop where the finish maker suggests. For painted projects, you can often stop at a slightly coarser grit than for a clear finish, since paint hides fine scratches and benefits from a little surface texture to grip. For shaping edges or smoothing end grain, expect to spend more time at each stage because end grain is rough and drinks up finish.
Between coats of finish, very fine abrasives take down dust nibs and raise a light scuff for the next coat to bond to. Use a light touch and clean the surface afterward. For metal, rust removal and paint preparation use different abrasives and grit sequences, so check the product guide.
- Pick the lowest grit that deals with the flaw, then move up one step at a time.
- Match the final grit to the coating, using the label on the finish.
- Test on a hidden area or scrap before sanding the visible surface.
- Use fine grits for any step that is mostly about smoothing, not removing.
Abrasive Materials and Backings
Grit tells you the size of the particles, but the particles themselves can be made from different materials, and the choice affects how well the sheet works on a given surface. Several common types are sold for home use.
Aluminum oxide is a widely used general-purpose abrasive that suits wood, metal and painted surfaces, and it is a common choice in sheets and discs. Silicon carbide is sharp and hard, and it is often used for wet sanding, for finishing between coats and for working on plastics, glass-like finishes and some metals. Garnet is a natural mineral often associated with hand sanding on bare wood, giving a fine finish but wearing relatively quickly. Ceramic abrasives are made for heavy-duty use, particularly with power tools and tough materials. Product packaging typically states what the abrasive is made for, so use that as your guide.
Backing material matters too. Paper backings are flexible and common for hand sanding and general use. Cloth backings are stronger and suit belts and demanding jobs. Film and foam backings flex around curves and give an even cut on contoured surfaces. Some sheets are coated for loading resistance, meaning they clog less when sanding gummy materials, such as paint or resinous wood.
The open coat or closed coat description refers to how densely the particles cover the backing. Open-coat sheets have gaps that reduce clogging, while closed-coat sheets cut more but fill faster. Read the label to see which is offered.
- Choose the abrasive type for the material you are sanding.
- Use the backing that suits the tool or the shape of the work.
- Keep different types of sheets separate and labelled.
Wet Sanding and When to Use It
Wet sanding uses water, or sometimes another lubricant, along with an abrasive made for the purpose. The liquid carries away particles, reduces dust and heat, and helps the sheet glide, so it can give a very smooth finish. It is commonly associated with polishing finishes between coats, smoothing certain paints and working on some plastics and metals.
Not every sheet can be used wet. Look for wet-or-dry on the packaging. Using ordinary paper with water can cause it to fall apart, and water can ruin some surfaces, such as untreated wood, which can swell or stain. Check that both the abrasive and the surface can tolerate moisture before you begin, and follow the finish maker’s directions.
The technique is simple, but it needs care. Keep the surface and the sheet damp, and rinse the sheet often to clear debris. Use light pressure and even strokes, and avoid concentrating on edges, where finish is thin and it is easy to cut through. Wipe the surface dry and examine it in good light. Let it dry fully before applying more finish or polish.
Wet sanding reduces airborne dust, but the slurry it creates can contain whatever was in the coating. Dispose of it according to local rules, and wear gloves and eye protection. Avoid using electric tools near water, and do not wet sand around electrical parts.
- Confirm the sheet and the surface can be used wet.
- Soak or dampen the sheet as the packaging suggests.
- Sand gently with even strokes and rinse often.
- Wipe clean, dry and inspect before the next step.
Spotting Grit Problems While You Work
A good habit is to check the surface regularly, not just at the end. Wipe away dust and look at it with light coming in from the side, which makes scratches and low spots stand out. If you can still see scratches from the previous grit, you need to keep sanding at the current one before moving on.
Common signals help you decide. If the surface looks patchy, with shiny areas next to dull ones, you have not sanded evenly and need to continue with the same grit. If the paper clogs quickly, the grit may be too fine for the amount of material you are removing, or the surface may be gummy, such as resin or paint. Change the sheet, and consider a different abrasive.
If you see deep scratches after a fine grit, a coarse particle may have contaminated the sheet or surface. Clean thoroughly, and keep coarse and fine sheets apart. If the surface feels smooth to the touch but finish still looks rough, check the grain: some woods raise their fibers when wet finishes are applied, and a light sanding after the first coat can fix it.
It is also useful to know when to stop. Going beyond the grit recommended on your finish does not necessarily improve results, and it can reduce adhesion or cause blotchy stain. Follow the label and be consistent across the whole piece, so the finish looks uniform.
- Check with raking light after each grit.
- Wipe the surface to see its true appearance.
- Change worn sheets promptly.
- Do not skip more than one step in the sequence.
Buying, Sorting and Storing Sandpaper
A well-organized stock of sandpaper saves time and money. Rather than buying everything at once, begin with a few grits that cover your typical work: a medium grit for leveling, a fine grit for smoothing and a very fine one for between-coat work. Add coarser or finer grits when a project calls for them.
Check the packaging for the grit number, the abrasive type, the backing and any wet or dry markings. Buy the sheet format that suits your method: full sheets can be cut or torn to size for hand sanding, while discs, belts and pads are made for particular tools. Confirm the size and hole pattern against your tool before buying.
Many sheets have the grit printed on the back, but the marking wears off. Write the number on the back of each sheet before you start, or keep sheets in labeled envelopes or a folder with dividers. This avoids the mistake of using a coarse sheet when you meant to use a fine one.
Store sandpaper flat and dry. Moisture can weaken the backing and make the grit shed, and heat can curl or warp the sheets. Keep it away from dust and oil. Do not store used sheets with new ones, and throw away sheets that are torn, clogged or worn smooth.
Replace your stock when sheets are brittle, curled or shedding particles. Dispose of used sandpaper according to local guidance, especially if it was used on old coatings or treated materials.
Ready to Buy? Start Here
If this guide helped you decide what to look for, these products are a place to start.
As an Amazon Associate we earn from qualifying purchases. Prices and availability are shown on Amazon.
A Sanding Sequence Checklist
Jumping between grits at random wastes effort and leaves scratches you will see later under a finish. A simple routine keeps the work predictable from the first pass to the last.
- Clean the surface and remove loose dirt, old flaking material and any nails or staples that could tear the sheet.
- Pick the coarsest grit that suits the job, and stop using it as soon as the flaws you came to remove are gone.
- Move to the next grit up without skipping too far. Each step should remove the scratches left by the one before it.
- Wipe away dust between grits so loose particles do not drag across the surface and make new marks.
- Check the surface in raking light from the side, where leftover scratches show up clearly.
- Finish with the grit that suits your coating, then wipe the piece one last time before you apply anything.
Most sequences use three or four steps. A common pattern is to go from coarse to medium to fine, doubling the number roughly each time. If you ever find yourself unsure, go back one grit rather than pressing harder.
Reading a Sandpaper Pack Label
The packaging carries more than the grit number, and a quick look at the details helps you buy the right sheet the first time. The large number is the grit. Smaller print usually tells you the abrasive type, the backing, the sheet size and whether the paper is meant for dry use, wet use or both.
Look for words such as “open coat” or “closed coat”. An open coat leaves gaps between the abrasive grains, which gives dust somewhere to go and slows clogging on soft materials. A closed coat packs the grains tightly and cuts faster on hard surfaces, but it can fill up sooner.
Backing weight is often shown with a letter. Lighter backings bend easily around curves, while heavier ones hold their shape on flat work and last longer under pressure. If the label lists a hook and loop or adhesive back, confirm it matches your sanding block or machine before you buy.
Finally, check the count. A multipack with several grits is useful when you are still learning what you need, whereas a single-grit pack makes more sense once you know your routine. Listings usually show the sheet size, so compare it with your block to avoid trimming too much waste.
Mistakes That Waste Sandpaper
- Pressing too hard. Heavy force clogs the paper, can leave deep marks and tires your hands. Let the grit do the cutting.
- Skipping grits by a wide margin. Going from a very coarse sheet straight to a very fine one leaves scratches that the fine paper cannot remove.
- Using a worn sheet for too long. Once the surface looks smooth and shiny, the paper is no longer cutting and is just rubbing.
- Sanding across the grain on wood. Cross-grain scratches show up clearly once a stain or clear coat goes on.
- Ignoring dust. Fine particles trapped between the paper and the work create tiny scratches and shorten the life of the sheet.
- Folding the paper sharply. Creases break the abrasive and leave bare lines on the backing.
A sanding block or a flat pad spreads pressure evenly across the paper and keeps surfaces level. Using only your fingertips tends to dig grooves along the lines of your fingers, especially on softer woods.
Dust, Masks and When to Check the Manual
Sanding creates fine dust, and some materials need extra care. Old paint on an older building may contain substances that call for specific handling, so look up official guidance from your local authority before disturbing it. Treated timber, certain composite boards and fillers also carry warnings from their makers.
A dust mask or respirator that is suited to the material, plus eye protection, is a sensible habit for most jobs. Always follow the instructions on the mask packaging about fit and suitability, and ventilate the workspace well.
When you use a powered sander, read its manual for the right paper type, sheet size and dust collection settings. Different machines hold paper in different ways, and an ill-fitting sheet can slip or tear. If a tool vibrates more than usual, makes a new noise or smells of burning, unplug it and have it checked by a qualified repair service rather than carrying on.
For finishes such as varnish, oil or paint, the product label often states the grit it works best over. Following that note gives a better bond than guessing from general rules.
Sanding Words in Plain Language
| Word | Meaning |
|---|---|
| Abrasive | The hard grain that actually cuts the surface. |
| Backing | The paper or cloth that carries the grains. |
| Clogging | Dust or residue filling the gaps and stopping the cut. |
| Feathering | Blending an edge so a repair fades into the surrounding area. |
| Tack cloth | A slightly sticky cloth for lifting fine dust before a coating. |
| Scratch pattern | The fine lines left behind by a grit. |
With these terms in hand, a product listing becomes much easier to compare.
How to Look Up a Grit: By Stage, Then by Material
A grit chart is fastest when you approach it in two steps rather than hunting for a single magic number. Step one is the stage of work: are you removing material, smoothing and refining, or preparing for and working between finishes? Each stage owns a band of the chart. Removal lives at the coarse end, refining in the middle, and finish preparation at the fine end. Step two is the material, which nudges you within the band: soft woods and soft finishes clog and scratch easily, so they reward the gentler end of a band and frequent paper changes, while hard woods and sound paint films tolerate the stronger end. Two-step lookup, stage then material, prevents the most common chart error, which is choosing a grit by the material alone and landing a whole band away from what the stage required.
Keep the sequence rule in view while you look numbers up: each step should remove the scratches of the step before it, and jumping more than roughly one step at a time leaves deep scratches that finer paper polishes around rather than removes. If the chart suggests a sequence, treat the sequence as the recommendation and the individual numbers as its servants. A reader who follows a slightly conservative sequence with fresh paper will beat a reader who picks perfect numbers and then skips half of them, every time, because sanding quality is mostly scratch-pattern management.
Grit Choices Worked by Stage and Material
Stage one: removal and shaping
Removal means old finish, paint, heavy marks, or shaping an edge, and it is the only stage where coarse paper is the right starting point. On bare softwood with a failed finish, begin at the stronger end of the removal band, work only until the finish and marks are gone, and stop: every extra minute at a coarse grit is depth of scratch you must later remove. On hardwood, the same stage can start slightly finer because the surface resists scratching a little better and the material removal is slower anyway. On metal, removal usually means rust and scale, where the paper choice pairs with working dry and changing sheets often, since loaded paper on metal quickly stops cutting and starts skating.
Stage two: refining the surface
Refining is where most of the time goes and where the finish is really decided. Work through the middle band in order, checking after each step that the previous scratch pattern has gone, which you judge by looking across the surface in raking light rather than straight down at it. Softwoods refine quickly and can jump to the finer end sooner, but they also dent and fuzz, so light pressure matters as much as number choice. Hardwoods reward patience: their refining steps take longer, and rushing shows up as a surface that looks smooth bare and then displays every scratch the moment finish raises the contrast. For plywood and veneered panels, refining must respect the thin face layer: stay at the gentle end of the band, sand by hand or with great care by machine, and never return to a coarse grit to fix a small mark, because sanding through the veneer is a one-way accident.
Stage three: preparing for finish and working between coats
Before a first coat, the final grit sets how the finish grips and how the surface feels, and the finish maker’s guidance outranks any chart, including this one, where the two differ. Paint generally wants a slightly stronger final preparation than clear finishes, because paint films hide fine scratch patterns that clear coats magnify. Between coats, the job shrinks to scuffing: a fine grit, a light touch, and the goal of uniform dullness rather than removal. Edges and corners get the lightest touch of all at this stage, since finish is thinnest there and sanding through an edge between coats creates a visible witness line that later coats emphasize.
The Pencil-Grid Test: Knowing When a Stage Is Done
The most reliable way to know whether the current grit has finished its work is to give it something visible to erase. Before you begin a refining step, scribble a light pencil grid across the whole surface: loose, wavy lines covering every area, in ordinary pencil, pressed lightly. Then sand as normal. The grid disappears unevenly: it vanishes first where the sander dwells and lingers in low spots, missed patches, and areas your pattern does not reach. When the last trace of pencil is gone, the current grit has touched everything, and the scratch pattern should be uniform. If you move on while pencil still shows in a hollow, that hollow still carries the previous, coarser scratches, and they will reappear under finish.
The test earns its keep in three situations. On large flats, it exposes the systematic misses at the edges of your sanding pattern that eyes alone forgive. On repaired or filled areas, it shows whether the filler and the surrounding wood are leveling together or at different rates. And when teaching a helper or checking your own work at the end of a long session, it replaces argument with evidence: either the grid is gone everywhere or it is not. Use a light hand with the pencil, especially on pale woods and before clear finishes, and sand the marks fully out at each stage rather than letting them accumulate; the final stage’s grid should be the faintest of all, more a breath of graphite than a drawing.
A close cousin of the grid test helps between coats: after scuffing, wipe the surface with a clean cloth and look across it in angled light. A properly scuffed coat looks uniformly dull, like frosted glass. Shiny islands in that dull field are unsanded or barely sanded spots where the next coat may not bond well. Mark them lightly with pencil, scuff again by hand, and recheck. Two minutes of this inspection prevents the peeling and patchiness that otherwise get blamed on the finish itself.
Reading the Surface: Three Checks Before You Move Up a Grit
Beyond the pencil grid, build three quick checks into every grit change. The hand check: run a clean palm slowly across the surface; your hand detects ridges, fuzz and rough patches that your eyes, looking straight down, routinely miss. The light check: hold a lamp low so light rakes across the surface and look along it, which throws scratches and dips into relief. The dust check: wipe the dust away completely before judging, because dust fills scratches and flatters the surface, and a surface judged through its own dust is being judged through a disguise. Passing all three checks means the stage is done; failing any one means another pass at the same grit, not a hopeful move to a finer one, since finer paper cannot remove what the current grit has left behind.
Worked Sanding Plans for Common Jobs
Plan one: a pine shelf to be painted
Pine is soft, resinous and quick to show scratches through paint if the sequence is rushed, but forgiving in every other way. Start by checking the surface for glue spots and raised grain rather than reaching straight for paper: glue resists both sanding and paint, and it is easier removed now. Work the refining band in order with light pressure, raising the grain deliberately if the paint is water-based: wipe the surface with a barely damp cloth after the middle step, let it dry, and take the raised fibers off with the final grit, so the paint does not raise them permanently later. The pencil-grid test is worth using on the flats, because pine’s pale color hides scratch patterns from the eye until the paint’s sheen reveals them. Finish preparation stops at the paint maker’s recommendation; going finer than paint wants wastes effort and can leave a surface so polished that adhesion suffers, which is the one direction of error beginners rarely suspect.
Plan two: an oak tabletop to be clear-finished
Hardwood under a clear finish is the most revealing combination in the chart’s world, so this plan is the most methodical. Removal is rarely needed unless the old finish has failed; where it has, take it off with the gentlest method that works and reserve paper for the aftermath. Refining proceeds through the full middle band without skipping, with a complete dust wipe and a raking-light check at every change, and the pencil grid on the final refining step, drawn faintly and erased completely. Before the finish, the surface gets the hand check with a palm and, for the truly careful, a wipe with a cloth that will snag on any remaining rough fiber and announce it. The final grit follows the finish maker’s sheet over the chart where they differ. Between coats, scuff lightly, inspect for shiny islands, and keep edges on a ration of attention, because a tabletop’s edges are where clear finishes are thinnest and sanding enthusiasm does its quiet damage.
Plan three: painted metal, such as a garden gate or a bike frame
Metal changes the plan’s emphases. The goals are rust removal where it has started, feathering the edges of sound paint so repairs disappear, and a uniform key for the new coat, all without thinning the metal or rounding its details. Work dry, change paper often because metal loads it quickly, and treat rust spots individually at a stronger grit before blending the whole surface at the stage’s gentler end. Feathering deserves its own patience: a hard edge between old paint and bare metal will print through the new coat, so the transition should be a slope you can feel only gradually with a fingertip. Where rust is heavy or the item is valuable, the manual-and-professional caution from the earlier sections applies: some coatings on older metal need specialist handling, and checking before sanding is part of the plan, not a delay to it.
Storing and Sorting Paper So the Chart Stays Usable
A grit chart fails in practice when the paper itself is chaos: unmarked sheets in a mixed pile, discs separated from their boxes, half-used pieces indistinguishable from new. A simple system keeps the chart’s advice executable. Store each grit in its own labeled envelope, sleeve or compartment, coarse to fine in order, so the sequence is physical and the next grit is literally the next slot. Mark the grit on the back of every cut piece the moment you cut it, in pencil, because a sheet’s identity survives exactly as long as its packaging unless you write it on. Keep partly used paper in a separate, clearly second-best place: it has honest work left in it for rough stages and for the pencil-grid erasing passes, but it should never mingle with fresh stock, or every stage becomes a lottery of unknown sharpness.
Buy in the sequence’s proportions rather than evenly. The middle refining grits do most of the work and wear out fastest, coarse grits are used briefly and last, and fine finishing grits are consumed steadily between coats. A drawer stocked evenly across all grits guarantees running out of the middle of the sequence mid-project, which tempts the worst sin in this whole subject: skipping the missing step. A small stock check before a project, against the plan’s sequence, takes a minute and belongs on the same mental checklist as charging batteries and finding the dust mask. The chart tells you which numbers the job needs; the storage system makes sure those numbers are in the drawer, labeled, and findable with dusty hands, which is where good intentions about grit usually end.
Grit and the Finish Maker’s Instructions: Who Wins?
Sooner or later the chart and a finish tin will disagree, a chart suggesting one final grit and the product’s instructions specifying another, and the reader deserves a clear rule: the finish maker’s instructions win on their own product. The maker has tested their coating on prepared surfaces and knows how it grips, flows and cures; the chart speaks in generalities across all finishes. The same hierarchy applies to abrasives made for a specific system, such as papers sold for a particular coating range. Where the maker’s guidance is silent, the chart governs, and where the two agree, which is most of the time, confidence is doubled. The practical habit is to read the finish instructions during planning, not with the brush in hand, and to write the maker’s final grit onto the project plan beside the chart’s sequence, so the sequence you actually sand is the reconciled one. Disagreements are usually small, a single step finer or coarser, but a small disagreement honored deliberately beats a large one discovered under a cured coat.
A One-Page Summary to Tape Inside the Sandpaper Drawer
Everything in this cheat sheet compresses, for daily use, into a card that fits inside the drawer where the paper lives. Write it in your own hand, because the writing fixes it in memory. Line one: the stage bands, removal, refining, finish preparation, with the grit ranges your own stock uses. Line two: the sequence rule, never skip more than one step, and the reason, each grit erases the last one’s scratches. Line three: the pencil-grid test in five words, scribble, sand, gone means done. Line four: the three checks before moving up, hand, raking light, dust wiped away. Line five: the material nudges you use most, softwood gentler and changed often, hardwood patient, veneer barely touched, metal dry and fresh paper. Line six: the finish maker’s number for the finish you use most, written when you read the tin. Six lines will not teach sanding, but they will run a sanding session, which is what a cheat sheet is for. The full page remains here for the new material, the unfamiliar finish and the problem surface; the card handles the ordinary Tuesday, and between them, the grit decision stops being a guess at any level of the craft.
Grit Choices for Repairs and Touch-Ups
Most of this cheat sheet imagines a whole surface sanded in sequence, but much real sanding is a repair: one damaged patch in an otherwise finished piece, a scuff on a floor, a drip in a painted door. Repairs break the sequence rule in a specific, disciplined way. Work only as coarse as the damage requires, and confine the coarse work to the damage itself, feathering outward through the finer grits over a widening area so the repair’s edges dissolve into the surrounding finish. Match the surrounding surface’s final grit rather than the chart’s ideal for the material, because the goal is invisibility, not perfection: a patch sanded noticeably smoother than its neighbors shows as clearly as a rough one under a sheen. Test the repair’s visibility the way the main guidance teaches, in raking light and, where possible, with a preview of the finish, and expect a repair on a visible surface to need its finish blended over a larger area than the sanding was. Small, patient and matched beats thorough, isolated and perfect, every time a repair meets a finished room.
Keeping This Cheat Sheet Current in Your Own Drawer
A cheat sheet ages in two ways: finishes change their recommendations, and your own experience quietly outgrows its generalities. Counter both with a light annual habit. When a finish you use changes its preparation guidance, write the new final grit on the drawer card the same day, in the place of honor the summary section describes. When a project teaches you something the chart does not say, a material that clogs faster than its family, a sequence that suits a finish you love, add it to the card’s margin or to a note kept with the paper stock, dated, so future you knows whether the note is fresh wisdom or an old experiment. Retire advice that your notes have contradicted twice; a cheat sheet is a tool, and like the paper it describes, it works best fresh, sorted and honestly labeled. Kept this way, the sheet in the drawer and the fuller guidance here stay in agreement, and the grit decision, from coarse removal to the last scuff between coats, remains what it should be: quick, boring and right.
Sandpaper and the Environment of the Workshop
One influence on grit performance rarely gets its own paragraph: the workshop itself. Paper stored in a damp space curls, its backing softens and its bond weakens, so the drawer this sheet lives in should be a dry one, off the floor and away from the wall that sweats in winter. Paper used in a cold room feels stiffer and cuts differently until it warms, which is one more reason test pieces matter in unheated spaces. Dust extraction and housekeeping feed back into grit life too, because a surface and a sheet kept clear of loose grit from earlier, coarser stages stop re-scratching each other. None of this changes a single number on the chart; all of it changes how faithfully the numbers perform, which is why experienced hands treat the storage of abrasives as part of the abrasive system itself, and why this cheat sheet ends where it began, with the unglamorous truth that sanding rewards the tidy.
And a last word for the reader who sands rarely and feels the chart’s detail is aimed at someone else: the occasional sander benefits most of all from the sheet’s discipline, because fluency cannot be relied on to fill the gaps that practice fills for the regular. Tape the drawer card up, follow the sequence without improvising, run the pencil grid without embarrassment, and the result will stand comparison with work done by hands that sand every week. Craft, at the level this page serves, is mostly the refusal to guess at the moments where a check exists, and grit is simply one of the places that refusal pays best.
If this page earns one permanent place in your workshop, let it be the habit it keeps returning to: stage first, material second, sequence unbroken, progress proven by the pencil grid rather than presumed. Grit numbers change with products and fashions; that order of thinking does not.
FAQ
What grit should a beginner use for most wood projects?
A medium grit followed by a fine grit covers many projects. Check your finish’s label for its recommendation.
Can I go finer than needed?
Yes, but very fine sanding can seal the wood so some stains absorb unevenly. Follow the label.
What is the difference between grit and the P scale?
Both describe particle size, but they follow slightly different standards, so numbers may not match exactly, especially at the fine end. Stay with one system for a job and check the packaging.
Can I reuse sandpaper?
Sheets that still cut well can be reused, but clogged or worn sheets only burnish the surface. Tapping or brushing off dust can help, but replace the sheet when it no longer cuts.
What grit should I use before painting?
It depends on the surface and the paint. Many paints bond well to a lightly scuffed, clean surface, and the paint maker's label gives the best guidance. Test on a hidden area when unsure.
Why is my sandpaper clogging?
Paint, resin, oil or too fine a grit for the amount of material being removed can all clog it. Try a different abrasive designed to resist clogging, clean the surface and change sheets often.
Is coarse sandpaper better for removing paint?
It cuts faster, but it leaves deep scratches and can gum up on soft paint. Scrapers or chemical strippers are sometimes more efficient. Be careful with old paint and follow local advice.
Do I have to sand with the grain?
On wood, sanding with the grain hides scratches best. Some coarse removal may go across the grain, but follow with finer grits along the grain to remove those marks.
How can I tell the grit of an unmarked sheet?
Compare it with labeled sheets by feel and appearance, or test it on scrap. If you are unsure, treat it as coarser than you think and work through finer, labeled sheets afterward.
How do I use the chart for a material it does not list?
Start from the stage band for your task, then adjust by resemblance: soft, easily scratched or easily clogged materials behave like the softwood entries and reward the gentler end of the band with frequent paper changes, while hard, sound surfaces behave like the hardwood entries. Test on an offcut or a hidden area first and let the pencil-grid test judge the result.
Why does the pencil-grid test use pencil rather than chalk or marker?
Pencil graphite sits on the surface without soaking in, sands away cleanly at the current grit, and shows clearly on most woods and cured finishes. Marker can bleed into bare wood and survive as a stain, and chalk dusts off too unevenly to reveal missed spots reliably. Use a light touch so the grid itself needs no extra sanding to remove.
I followed the sequence but scratches still show under the finish. What went wrong?
Usually one of three things: a stage was ended before its scratch pattern was uniform, which the grid test is designed to catch; a grit step was skipped, leaving deep scratches that finer paper polished around; or dust from a coarser stage contaminated a finer one. Work clean between stages, vacuum or wipe the surface at each change, and store grits separately.
The Short Version
Low numbers cut fast and high numbers smooth. Work up through the grits in order, keep the dust under control, and follow the finish maker’s guidance.


