
Different woods cut, hold fasteners, and look in different ways. This cheat sheet describes familiar kinds in general terms so you can narrow down what to look for. Properties vary from board to board, so treat the table as a rough guide, not a promise.
Common Woods at a Glance
| Wood | Group | General character | Often used for |
|---|---|---|---|
| Pine | Softwood | Light, soft, easy to cut, may dent | Shelves, frames, practice projects |
| Fir | Softwood | Straight grain, fairly strong for its weight | Framing and construction |
| Cedar | Softwood | Aromatic, naturally resists moisture | Outdoor items, fences |
| Poplar | Hardwood | Fairly soft for a hardwood, even texture | Interior projects, hidden parts |
| Oak | Hardwood | Hard, pronounced grain | Furniture, flooring |
| Maple | Hardwood | Hard, fine grain | Cutting boards, workbench tops |
| Walnut | Hardwood | Dark, medium-hard, workable | Fine furniture |
| Plywood | Engineered | Layered, stable, resists warping | Cabinets, panels |
In this guide
Softwood or Hardwood
The names refer to the type of tree, not always to how hard the wood is. Softwoods come from conifers and are usually easier to work. Hardwoods come from broadleaf trees and often wear better but can be harder on blades and bits.
What to Look For When Buying
- Flat, straight boards without twists or bows
- Few large knots in spots that must bear load
- Dry wood, as wet boards shrink and move
- Grain direction suited to how the piece will be cut
Matching Wood to Project
For practice and simple builds, softwoods keep the cost of mistakes low. For furniture that will see daily use, a hardwood or good plywood is common. Outdoors, choose wood labeled for outdoor use and check the maker’s guide for finishing needs.
Different woods call for different habits. Soft woods can dent under a hammer or a clamp, so protect them with scrap pads. Hard woods can burn if a blade or bit is dull or the feed is too slow. Some woods split easily near board ends, which is where pilot holes help. Dust from certain woods can irritate eyes, skin, or lungs, so wear a dust mask and control the dust. Read the finish label to see how each type takes stain or a protective coat.
Names can be confusing because the same label may cover several related trees, and lumberyards sometimes group boards under a single name. If appearance matters, look at the actual board rather than relying on the name alone. If strength matters, ask the supplier or check the maker or grader markings on structural lumber, and consult a qualified professional for load-bearing uses.
A Worked Example: Choosing Wood for a Bookshelf
Suppose you want a freestanding bookshelf for a spare room. Here is a way to move from the cheat sheet to a decision.
- List the demands. Books are heavy, shelves must not sag, and the unit will sit indoors in a normal home, so stability and stiffness matter more than rot resistance.
- Narrow to families, not names. Softwood boards, a hardwood such as oak or poplar, or plywood for the sides and shelves are all possible directions.
- Weigh the trade-offs. Softwood is easy to cut but dents. Hardwood resists wear but is harder to work. Plywood is stable and flat, but its edges need covering for a neat look.
- Look at the real boards. Check for straightness, knots in the span where shelves carry load, and dryness.
- Plan the finish. Some woods take stain evenly, while others can look blotchy, so read the finish label and try a sample on an offcut.
- Buy a little extra. Spare material lets you replace a piece that splits or turns out to be warped.
Common Scenarios
A practice project such as a simple box
Softwood is forgiving and widely available, so mistakes are inexpensive in material terms. Pine or a similar board lets you learn cutting and joining without struggling against dense grain.
A kitchen board or butcher-style surface
Dense, fine-grained hardwoods are commonly chosen for surfaces that meet food. Check that the wood and any finish are suitable for contact with food, using the finish maker’s guidance.
An outdoor planter or garden bench
Choose wood sold for outdoor use or a species noted for resisting moisture, and read the maker’s guide on finishing and maintenance. Even durable species weather, so plan for upkeep.
A cabinet carcass or large flat panel
Solid wide boards move with humidity, which can crack panels or open joints. Plywood and other manufactured boards stay flatter, so many people use them for large panels and add solid wood edging.
Decision Table: Which Direction to Look In
| If the project needs | Look first at | Watch out for |
|---|---|---|
| Easy cutting and low risk | Softwood such as pine | Dents, knots and resin |
| Wear resistance and good looks | Hardwood such as oak or maple | Blunt tools and tear-out |
| Flat, stable panels | Plywood | Exposed edges and thin surface layers |
| Outdoor use | Wood labelled for outdoor use | Weathering and finish upkeep |
| Hidden or covered parts | Poplar or similar | Marks easily if left unfinished |
Mistakes to Avoid
- Choosing by name alone. The same name can cover several related trees, and quality varies from board to board.
- Using damp wood. It shrinks as it dries, which opens joints and can warp the piece.
- Ignoring grain direction. Cutting and planing against the grain tears the surface, and short grain at a board’s end splits easily.
- Using softwood where wear is heavy. A frequently handled edge or seat will dent and mark more readily.
- Forgetting dust protection. Dust from some species can irritate eyes, skin or lungs, so wear a mask and use dust control.
Care and Upkeep of Wood and Projects
Store boards flat or evenly supported, with air able to reach all faces, and keep them off concrete floors and out of damp. Let wood settle in the room for some days before you cut it. Once a piece is finished, keep it away from direct heat and strong sunlight where you can, since rapid changes can cause cracking. Wipe spills quickly, refresh finishes as the label suggests, and expect seasonal movement in solid wood.
How to Read a Board Before You Buy
Names on a rack only tell part of the story. Learning to read the board itself helps you pick well, even when you cannot identify the species with certainty.
Grain patterns
Look at the end of the board. Tight, straight lines generally mean a stable piece cut from near the center of a log, while wide, curved arcs often indicate flatsawn lumber, which tends to cup more as moisture changes. Quartersawn boards show straighter lines on the face and usually move less across their width, although they can cost more and are not always on offer.
Color and figure
Color varies between boards, between the heartwood at the center of a tree and the lighter sapwood near the bark. If you want a consistent look, hold boards side by side in good light before you decide. Remember that many woods darken or lighten with exposure and with finishing.
Weight and feel
Two boards of the same size can feel very different in your hand. A heavier piece is generally denser, harder to cut and likely to hold screws well, though it may also split without pilot holes. A very light board may dent easily but is simple to carry and cut.
Defects to avoid
- Knots, especially loose ones that may fall out or large ones near an edge.
- Cracks and splits at the ends, called checks.
- Bark edges or soft, discolored patches that suggest rot or insect damage.
- Wane, where the board has a rounded edge from the outside of the log.
- Stains or fuzzy patches that may signal moisture trouble.
Surface condition
Rough-sawn boards need milling or heavy sanding, while surfaced boards are smoother but may be a little thinner than their labels say. Check the real thickness and width when planning your cut list, because nominal sizes at the yard often differ from actual measurements.
Working Properties Beginners Notice First
Once a board is home, the way it behaves under tools matters more than its name. These are general tendencies, not guarantees, and any given board may differ.
- Cutting: Soft species cut quickly but can tear at the edges. Dense species need sharp blades and a steady feed, otherwise the blade may burn the wood.
- Drilling and screwing: Pine and other soft woods grip screws less tightly but rarely split. Hard woods hold screws strongly but often need pilot holes and sometimes countersinking.
- Planing and sanding: Fine-grained woods tend to finish smoothly. Open-grained woods may need filler for a glass-smooth finish, and resinous woods can gum up sandpaper and blades.
- Gluing: Most common woods glue well with ordinary wood glue, but oily or resinous species can resist adhesion unless the surface is freshly cut or wiped as the glue maker advises.
- Finishing: Some woods take stain evenly, others turn blotchy. A sample piece and a conditioner, if the finish maker recommends one, can prevent surprises.
Sizing, Grades and Lumber Terms
Yard labels can read like code. A short glossary of everyday terms keeps you from paying for something you do not need.
| Term | Plain meaning | Why it matters |
|---|---|---|
| Nominal size | The name of a board, such as 2×4 | Actual dimensions are smaller after drying and planing |
| Board foot | A unit of volume for hardwood, 12 by 12 by 1 inch | Used to price many hardwoods |
| S4S | Surfaced four sides | Smooth and ready to use, though a little thinner |
| Rough sawn | Left as it came from the saw | Needs milling to be flat and smooth |
| Kiln dried | Dried in a controlled chamber | Generally more stable than air-dried or green wood |
| Select or common grade | Quality rankings that vary by species and region | Higher grades have fewer defects; ask what the grade means locally |
Grades are set by industry bodies and differ between softwood and hardwood and between countries, so ask the supplier how their labels work and treat the summary above as a starting point. For structural work, look for grade stamps and consult a qualified professional.
Sustainability, Sourcing and Cost Thinking
Price differences between woods can be large, and they do not always match quality. Availability changes with region, season and supply, so it is better to compare prices at your own supplier than rely on a general ranking. Common softwoods are usually the lowest in cost per board, mid-range hardwoods sit in the middle, and showy or scarce species cost more.
- Look for lumber marked with a recognized forestry certification if sourcing matters to you, and ask the supplier where the wood comes from.
- Reclaimed lumber can be rewarding but may hide nails, paint with unknown content, or old finishes. Check carefully and avoid sanding painted wood from older buildings without first learning what the paint contains.
- Plywood and other engineered boards make efficient use of timber and can cut waste for large panels, although the glue and surface veneer vary by product, so read the maker’s information about suitability.
- Buy a little more than the project needs to allow for defects and mistakes, and plan cuts so that short offcuts become small parts.
- Keep offcuts for test finishes and joinery practice.
Pressure-treated and chemically preserved lumber needs particular care. Follow the maker’s handling directions, wear gloves and a dust mask when cutting, do not burn offcuts, and do not use it for food-contact items unless the maker states it is suitable.
A Beginner Sampling Plan
Reading about wood only goes so far. A simple plan helps you learn quickly without spending much.
- Buy short lengths of three or four different woods, such as a softwood, a mid-range hardwood and a sheet of plywood offcut.
- Label each piece on the back with a marker so you can keep track after sanding.
- Cut each with the same saw, then drill a hole and drive a screw to feel the difference in resistance.
- Sand a section on each, wipe it clean and apply the same finish to half the piece.
- Compare the results once the finish has dried, and write brief notes on how each one cut, sanded and looked.
- Keep the samples on a shelf for later reference, and add new species as you meet them.
This habit builds your own record of how woods behave with your tools, which is more reliable than any generic chart.
Common Beginner Questions About Wood Names
Shopping for lumber brings up naming problems that can confuse anyone new to the craft. Keeping a few ideas in mind makes labels less mysterious.
- Trade names often group several related species. A board sold as white oak or red oak may include more than one tree, and the grouping is based on appearance and behavior rather than strict botany.
- Regional names differ. A wood called one thing in one area may have another name elsewhere, so describe what you need by use and ask the supplier what they recommend.
- Some labels are marketing. Names that sound exotic do not guarantee unusual qualities. Look at the board and ask about its source.
- Lookalikes exist. Some woods are stained to resemble others, so ask whether a board is natural or colored if the color matters.
- When you want a particular species for a job, write the name on your shopping list along with a fallback, and ask about alternatives if stock is short.
A good local supplier is a helpful resource. Explain your project, your tools and your budget, and ask which boards are in stock today. Staff usually know which pieces are straight, dry and ready to work.
Keeping Notes on Species You Use
A simple notebook or phone file becomes a personal cheat sheet over time. For each wood you try, record the date, where you bought it, how it cut, how it took screws and glue, and how the finish looked. Add a small photo of the end grain and the finished surface. After a few projects, you will have far more useful information about your own tools, your own climate and your suppliers than any generic table can offer.
Hardwood and Softwood in Plain Words
The terms hardwood and softwood describe the type of tree, not always how hard the wood feels. Broadly, hardwoods come from broadleaf trees and softwoods from conifers, though there are exceptions. For beginners, a rough guide to common species helps avoid frustration. Check the supplier’s description for the exact grade and properties of any board you buy.
- Pine and fir: common softwoods, easy to cut and affordable for framing and simple projects.
- Oak: a hardwood known for strength and a visible grain pattern.
- Maple: a hardwood with a tight grain, often used for work surfaces and furniture.
- Cherry: a hardwood that deepens in color over time.
- Walnut: a darker hardwood often used for fine furniture.
Quick Comparison
| Species | General feel | Typical use |
|---|---|---|
| Pine | Soft, light, easy to work | Shelves, frames, practice pieces |
| Oak | Hard, heavy, strong | Furniture, floors |
| Maple | Hard, smooth | Tabletops, cutting surfaces |
| Poplar | Moderate, takes paint well | Painted furniture and trim |
Tips When Choosing
- Begin with softer species when you are learning basic skills.
- Consider how the wood will take stain or paint.
- Check boards for straight grain and knots.
- Ask the supplier about drying and storage.
Grain, color and hardness vary within a species, so treat these descriptions as general guidance. When a project has special needs, such as outdoor use or food contact, check with the supplier and follow maker’s and official guidance for suitable wood and finishes.
A simple habit is to keep small offcuts of each species you work with. Labeling them and finishing one side lets you compare how each takes stain or oil, and builds a personal reference that grows with your experience.
Using the Wood Cheat Sheet to Choose With Confidence
The tables above compress a lot of hard-won knowledge into a small space: which woods are hard or soft in the working sense, which take finish gracefully, which forgive beginners and which punish them. But a cheat sheet only helps if you know how to run a real decision through it. This section does exactly that — how to read a row of the sheet properly, how to walk from a project idea to a chosen species step by step, how to decide between the final two candidates that every real choice comes down to, and how to avoid the misunderstandings that make beginners buy beautiful wood for the wrong job.
Read Across the Row, Not Down the Names
Beginners usually read a species list as a league table, hunting for the “best” wood. The sheet is not built that way. Each row describes a personality: how the wood feels under tools, how it behaves when glued and finished, how it looks once a finish deepens its colour, and what it tends to cost in effort even before money enters the picture. Reading across one row tells you what working with that species will actually be like on a Saturday afternoon, which is the information a project decision needs.
Pay particular attention to two columns readers skim: workability and movement. Workability predicts your experience — whether the wood planes cleanly or tears, whether it sands willingly or clogs paper, whether edges stay crisp or crumble. Movement predicts the project’s future — how much the finished piece will swell, shrink, and stress its joints as the seasons change in your home. A species can be delightful on the first count and troublesome on the second, and the sheet’s honesty about both is what makes it worth consulting before the purchase rather than after the disappointment.
A Step-by-Step Choice, Worked in Full
Take a typical first furniture project: a small bedside table with a drawer. Step one, list the demands before naming any species. The top will be seen and touched daily and should resist modest dents; the drawer sides need to slide and stay stable; the whole piece should be buildable with beginner tools and forgiving of beginner joinery. Step two, take those demands to the sheet and mark every species whose row fits them — usually a small set of familiar, moderately priced, well-behaved woods rather than the exotic end of the table. Step three, split the choice by part, because the sheet quietly encourages this: nothing requires one species throughout, and a harder-wearing wood for the top with a lighter, stable wood for drawer sides is a classic, sensible combination. Step four, check availability in the sizes you need, since a species the sheet loves but your supplier stocks only in awkward dimensions will cost you time and waste. Step five, buy a small extra amount of the chosen wood and make your test finishes and practice joints in the offcuts, converting the sheet’s descriptions into your own experience before the real pieces are committed.
The self-check at the end is simple. Can you say, for each part of the project, which row of the sheet justified the species chosen? Can you name the property that would make you change your mind — a top that dents too easily, a board that moves too much for a wide panel? If you can answer both, the choice was made from the sheet’s evidence. If you chose mainly because the wood looked beautiful in the store, the sheet is asking you to run the decision once more, because beauty is one column among several and rarely the one that decides whether a project succeeds.
The Final Two: How Real Choices Get Settled
Most honest lookups end with two candidates, and the tie-breakers are practical rather than romantic. Choose the one whose working properties suit the tools you own today, not the tools you hope to own. Choose the one your supplier stocks consistently, so a second board bought next month resembles the first. Choose the one whose mistakes are cheaper to learn on — every beginner ruins a board eventually, and there is real wisdom in ruining an affordable, replaceable one while your hands learn. And choose the one whose finished colour you like under the finish you will actually apply, tested on an offcut, because species change character under oil or varnish in ways the sheet describes but only a sample proves.
Misreadings That Trip Beginners
The first is treating “hardwood” and “softwood” as hardness scores; the sheet’s opening sections explain that these are botanical families, and some softwoods work harder than some hardwoods. Judge by the row’s described properties, never by the family label. The second is assuming a species that is easy to buy as flooring or furniture will be equally easy to work by hand — industrially processed material hides a species’ difficult habits behind factory machinery. The third is ignoring grain direction and board selection because the sheet is about species; within any species, one board can be straight-grained and calm while its neighbour twists, and the sheet’s buying guidance matters as much as its species rows. The fourth is choosing a famously beautiful species for a first project in a demanding design, stacking a difficult material on top of difficult joinery; the sheet’s beginner-friendly rows exist so that your first projects teach skills instead of survival.
Growing Your Own Sheet
The printed cheat sheet is a starting map; the territory is your own workbench. Keep offcuts of every species you use, labelled, with one face finished the way you finished the project. Note on the back how it planed, sanded, glued, and dented in service. Within a year or two you will own a personal reference that no general sheet can match, because it records these species as they behaved in your hands, with your tools, in your home’s air. Bring that growing sample set to every new decision, and let the general sheet do what it does best: introduce you to species you have not met yet, and warn you fairly about the ones whose personalities you have not yet learned to handle.
From Species to Board: The Second Half of Choosing
Choosing a species settles only half the decision; the other half happens at the rack, board by board. Two boards of the same species can differ more in behaviour than two neighbouring species on the sheet. Carry the sheet’s priorities with you into that moment. Sight along each board for bow and twist, because a beautiful species in a warped board is a project spent fighting the material. Look at the end grain to judge how the board was cut and how it is likely to move. Check both faces for the defects the sheet’s buying guidance lists, and be suspicious of a board whose worst face has been turned to the wall of the rack.
Weight matters too, in the literal sense: a board that feels unusually heavy for its species may still hold moisture, and one that feels light and rings brightly when tapped is usually dry and lively. None of these checks appears as a column in any cheat sheet, yet they decide as much as the species name does. The sheet narrows the world to the right species; your hands and eyes, in the aisle, narrow it to the right boards — and learning to enjoy that second narrowing, rather than rushing it, is one of the pleasures the craft offers for free.
Keeping a Species Diary Across Projects
Every project teaches something about the species it used, and nearly all of that teaching evaporates unless it is written down while the sawdust is still on your shoes. Keep the diary brief or it will not survive: the species, the project, one thing the wood did that pleased you, one thing it did that surprised you, and whether you would choose it again for the same job. Surprises are the valuable entries. The species that tore out under the plane despite its gentle reputation, the modest board that took a finish like glass — these are the data points that slowly correct the general sheet into your personal truth.
Review the diary whenever the sheet and your memory disagree about a choice. Memory is a biased archivist; it keeps the triumphs and misfiles the disasters. The diary, kept honestly, is how a beginner’s reliance on a printed cheat sheet matures into a maker’s judgement — not by discarding the sheet, but by annotating it with evidence until the annotations become the part you trust most, and the sheet becomes what it always wanted to be: the introduction, not the authority.
Wood Choices for the Rooms You Actually Live In
The cheat sheet describes species in general terms, but your projects will live in particular rooms, and rooms have opinions. A kitchen subjects wood to steam, splashes, and daily wiping; a hallway subjects it to knocks and grit carried in on shoes; a bedroom asks mostly for calm appearance and a surface pleasant to touch. Reading the sheet through a room’s demands sharpens every choice. In the kitchen, the rows describing stability and tolerance of moisture deserve double weight, and the finish you pair with the species matters as much as the species itself. In the hallway, hardness in the working sense — resistance to dents that show — moves up the list. In quiet rooms, grain and colour finally get the vote that beginners want to give them everywhere.
Light deserves a mention too, because species change under it. Many woods deepen in colour with exposure while others fade, and a board chosen under a supplier’s lighting may settle into a noticeably different tone on your wall within a year. The sheet’s descriptions of finished appearance are your warning system here; where a species is known to shift, either embrace the shift as part of the design or choose a steadier species for pieces that must match existing furniture. Testing a finished offcut in the actual room, across a few days of changing light, remains the cheapest insurance in all of woodworking — cheaper than any upgrade of species, and more informative than any photograph.
When Two Species Should Share One Project
Combining species is usually introduced as a design flourish — a pale top on a dark base, a contrasting drawer front — but the cheat sheet supports it for practical reasons as well. A project can borrow each species’ strengths: the stable, inexpensive wood where structure hides, the beautiful or hard-wearing wood where eyes and hands land, the easy-working wood where joinery is intricate. The cautions are equally practical. Species sharing a panel or a glue line should move at compatible rates, or the seasons will argue inside the joint. Species sharing a surface should accept the same finish predictably, which is a question for test offcuts, not optimism. And the combination should be decided at the sheet, before purchase, because a pairing invented at the rack under time pressure tends to be two favourites rather than two partners.
Start simply if you are new to mixing: one dominant species, one accent, joined in ways that let each be itself. Note the pairing in your project records with a sentence about how it behaved — how the glue line fared, how the finish unified or separated the tones, whether you would repeat it. Those sentences accumulate into the most personal page of your own extended cheat sheet: not what the species are, but what they do together, in your rooms, under your finishes, in your hands.
Species, Sustainability, and the Story in the Board
The cheat sheet’s sourcing material invites one more reflection that belongs in every beginner’s education: a board is a piece of a tree that grew somewhere, over decades, and the choices on the sheet are therefore also choices about forests. None of this requires guilt or grand gestures; it asks only for the ordinary respect of using material well. Buy what the project needs rather than what anxiety suggests. Design so that offcuts are large enough to become something else. Keep the sample library and the species diary this guide recommends partly because they are, in effect, a record of trees honoured by being understood rather than wasted through ignorance. A maker who can name the species in a finished piece, and say why each was chosen, is practising a form of attention that industrial furniture quietly abandoned — and customers, family members, and future inheritors of the piece can feel the difference even when they cannot name it.
Local and reclaimed material deserve their place in this reflection. A species your region grows, milled nearby, arrives with a story and often with working properties suited to your climate, since the tree lived in it. Reclaimed boards arrive with history and hazards in equal measure — character in the grain, and sometimes metal in the depths — and the sheet’s buying guidance about inspection applies to them doubled. Either way, the habit the cheat sheet has been building all along serves here too: know what the material is, know what it asks of you, and let the project, the place, and the tree negotiate the final choice together. That negotiation, repeated across a making life, is how a beginner’s reference sheet matures into something no publisher can sell: a personal philosophy of material, written in finished work.
The Cheat Sheet’s Real Promise
No table can choose a board for you, and this one never pretended to. What it promises is narrower and more valuable: that your choices will be informed ones, made from the properties that actually decide a project’s fate rather than from a name, a price, or a beautiful grain pattern glimpsed under store lighting. Keep pairing the sheet with the habits built around it in this guide — the offcut tests, the labelled samples, the diary, the second look at the board itself — and the species question gradually stops feeling like a gamble. It becomes a conversation between the project’s needs and the material’s character, conducted in a vocabulary the sheet taught you.
That conversation is one of the permanent pleasures of working wood. Years from now, the specific rows will have faded, but the way of seeing will remain: grain as structure, species as personality, every board as a particular tree with opinions about your design. Makers who see that way waste less, choose better, and finish pieces that suit their material so naturally the joinery almost disappears. It begins, improbably, with a cheat sheet for beginners — and with the decision, which you have just practised throughout this guide, to read it slowly and take it seriously.
One Last Habit: Smell, Touch, and the Fresh Eye
Before any board leaves the rack with you, give it the three checks no sheet can perform. Smell it if the species is one whose scent is part of its character, because experienced makers genuinely identify and judge wood this way, and a board that smells wrong for its name deserves a second look at the label. Touch it — run a palm along both faces — because your hand detects the slight roughness of raised grain, the coolness of lingering moisture, and the silk of a well-kept board faster than your eyes can, and it will also find the splinter the polite way, now, rather than the rude way at the bench. Then look once more with the fresh eye the whole trip has been training: is this the species the project asked for, in the board the project deserves, at a price your notes will not make you regret? Three senses, ten seconds, and the cheat sheet’s work is complete — handed over, as all good references eventually are, to the judgement of the person holding the wood.
FAQ
Is plywood real wood?
It is made of thin wood layers glued together. It behaves differently from solid boards but is widely used.
Which wood is easiest to cut by hand?
Softwoods such as pine are generally easiest, though sharp tools matter more than species.
Is hardwood always better than softwood?
No. Each has strengths. Softwood is lighter, easier to work and widely used in construction. Hardwood often wears better and looks richer, but suits some projects and not others. Choose by what the piece has to do.
Why does the same species look different between boards?
Wood is natural, so colour, grain and density vary with the tree, the part of the log and how the board was cut. Compare boards in person under good light when appearance matters.
How do I know if wood is dry enough?
Ask the supplier how the wood was dried and how it was stored. A moisture meter can give a reading if you have one, and letting boards sit in your workspace before cutting helps them settle. Follow the maker’s guidance for any structural use.
Can I mix different woods in one project?
Yes, and many pieces do, such as a hardwood top on a softwood frame. Keep in mind that different woods move by different amounts with humidity, so allow room for movement in wide joints and use fasteners and glues that the maker approves for the combination.
What is the difference between flatsawn and quartersawn lumber?
Flatsawn boards are cut tangent to the growth rings, which gives broad arcs on the face and more movement across the width. Quartersawn boards are cut with the rings closer to vertical, showing straighter grain and usually moving less. Quartersawn is often harder to find and may cost more.
What does board foot mean when buying hardwood?
A board foot is a unit of volume equal to a piece 12 inches wide, 12 inches long and 1 inch thick. Many hardwood suppliers price by it. To estimate, multiply thickness in inches by width in inches by length in feet, then divide by 12.
Which woods are best for a beginner to practice joinery on?
Softwoods like pine are forgiving and inexpensive, so mistakes cost little. Once you gain confidence, try a mid-range hardwood such as poplar to feel how denser material behaves under chisels and saws. Sharp tools matter more than species at first.
Can I use pressure-treated wood indoors?
Many makers advise against using it for indoor living spaces or food-contact items. If you need to work with it, wear gloves and a dust mask, follow the maker’s handling directions and local rules, and ask the supplier or maker whether the product suits your intended use.
Why are lumber sizes smaller than their names?
A board called 2×4 is named for its size before drying and planing. After processing, the finished piece is smaller. Hardwoods are often sold by rough thickness that is later surfaced. Always measure the actual board before planning cuts and joints.
Why does the same species look different from one board to the next?
Because a species name describes a family of trees, not a single uniform material. Growing conditions, the part of the tree the board came from, and how it was sawn and dried all shift colour, grain, and working behaviour within one species. This is why the cheat sheet describes tendencies rather than guarantees, and why inspecting the actual boards — as the buying sections describe — matters as much as choosing the species name.
Is a more expensive species always better for a project?
No. Price mostly reflects scarcity, transport, and demand, not suitability. An expensive species can be harder to work, more prone to movement in your climate, or simply wasted on a project whose demands a modest species meets perfectly. Match the row’s properties to the project’s needs first; let price act as a tie-breaker between suitable candidates, never as the selection method itself.
How do I choose wood for an outdoor project?
Start from the sheet’s guidance on durability and weather behaviour rather than appearance, because outdoors the environment is the dominant demand. Then weigh how the piece will be finished and maintained, since many species survive outside only as part of a system — the right finish, renewed on schedule, and a design that sheds water instead of trapping it. When in doubt, favour the species your local suppliers recommend for local weather; regional experience is a column no printed sheet can include.
What should I do when my supplier does not stock the species I chose?
Return to the sheet with your project’s demands, not with the species name. Find the rows whose properties most closely match the species you wanted — similar working behaviour, similar stability, similar finished appearance — and choose among what is actually available. Substituting by property rather than by name keeps the project’s design intact, and it is one of the most useful habits the cheat sheet teaches.
The Short Version
Softwoods are easy to practice on, hardwoods are tougher and often better looking, and plywood is stable for panels. Decide what the piece must do, then inspect each board in person. Follow local rules and a qualified professional’s advice for structural work.


