Skip to content
RESEARCH-BASED GUIDES. PRACTICAL EVERYDAY ADVICE.How we pick products
UMTUMT Smart ToolBetter informed. Better equipped.
Workshop

Vacuum Belt Replacement: A Beginner’s Walkthrough at Home

Brush roll not spinning? This beginner walkthrough shows how to unplug, open the base, remove the worn belt and fit a new one the right way.

We may earn a commission from qualifying purchases. How we pick products

Vacuum Belt Replacement: A Beginner's Walkthrough at Home

A vacuum whose brush roll no longer spins often has a stretched or broken belt. Unplug the machine, open the base plate, slide off the old belt and loop the new one around the motor shaft and brush roll. The job normally takes around fifteen minutes with a screwdriver. This guide covers diagnosis, the swap, a worked walkthrough, realistic cases and the habits that make belts last.

Signs the Belt Is the Problem

Before opening anything, look for the usual clues. A burning-rubber smell, a roll that turns freely by hand but not under power, or a loose, shiny band in the base all point to the belt. If the roll will not turn even by hand, something may be wound around the ends, which is a different fix.

  • The brush roll stays still while the motor hums
  • Pieces of black rubber inside the base
  • A belt that looks stretched, glazed or snapped
In this guide

How the Drive Works

In many upright vacuums, a small motor shaft drives the brush roll through a rubber belt. The belt loops around the shaft and around a groove or a pulley on the roll. Because the belt grips by friction and slight tension, it wears with use: it can stretch, harden or get glazed, and it can snap if the roll jams. Some machines have a belt that is flat, some round, and some ribbed, and some models drive the roll directly with no belt at all. The manual shows which design you have. A belt that has snapped when a sock or a cable jammed the roll will usually snap again unless the cause is removed, so check the roll before blaming the belt.

Swapping the Belt Step by Step

  1. Unplug the vacuum from the wall. Never work on it while connected to mains power.
  2. Lay the machine flat on a towel or a clear table so you can see the underside.
  3. Remove the screws or release the clips holding the base plate, following the maker’s manual for your model.
  4. Lift out the brush roll. Cut away hair and thread wound around the ends with small scissors.
  5. Slip off the old belt and note which way it ran.
  6. Loop the new belt over the small motor shaft first, then stretch it around the brush roll’s belt groove.
  7. Place the roll back in its end caps and spin it by hand. The belt should sit flat and travel straight.
  8. Replace the base plate, fit every screw, and test the machine briefly on a hard floor.

A Worked Walkthrough

Imagine an upright vacuum that makes a motor noise but leaves the carpet looking untouched. This is a typical order of work.

  1. Unplug the cord and, if the machine has a removable bin, empty it. Tilt the vacuum back onto a towel.
  2. Spin the brush roll by hand. If it turns freely and the belt is limp or missing, the belt is the likely cause. If it is stiff, look for tangles.
  3. Take a photo of the underside, then undo the base plate screws. Place them in a cup so none are lost.
  4. Lift out the roll and cut away hair with scissors, taking care not to cut the bristles. Pull any thread out of the end caps.
  5. Inspect the motor shaft. It should be clean and free of melted rubber. Wipe it with a dry cloth.
  6. Hook the new belt over the shaft, then around the roll while holding the roll in place. Rotate the roll a few times by hand so the belt settles in its groove.
  7. Refit the plate, plug in, and run the vacuum briefly while holding it off the floor, if the maker’s manual allows. Listen for scraping or smell for heat.
  8. Test on the floor, and unplug and recheck if the roll stops or the belt slips.

Getting the Right Part

Factor Why it matters What to check
Belt shape Flat, round and ribbed types are not interchangeable Compare with the old belt
Length and width Too loose slips; too tight strains the motor Model number in the manual
Fit for your model Makers use different parts The maker’s parts list

If the cord is damaged, the motor smells of burning, or the machine trips a breaker, stop. Electrical faults are a job for a qualified professional or the maker’s service channel.

Common Scenarios

The new belt snaps quickly

Check for a jammed roll, worn bearings or a rough edge on the end cap. A part that drags will keep breaking belts.

The belt keeps slipping off

Look for a roll that is not seated, a worn belt groove, or a belt that is a size too long. Confirm the part number in the manual.

The roll spins but the vacuum smells hot

Stop using it and unplug it. Overheating can come from blockages or a failing motor, and a qualified repairer should check it.

You have pets or long hair at home

Hair winds around the roll ends more often. Cut it away after heavy use to protect the belt and bearings.

Mistakes to Avoid

  • Working while plugged in: an accidental switch-on while your fingers are near the roll can cause injury.
  • Stretching the belt too far when fitting: over-stretching weakens it before it has done any work.
  • Ignoring tangles: hair bunched near the bearings makes the roll drag and stresses the belt.
  • Losing screws of different lengths: keep them in order, as the wrong screw can poke through plastic.
  • Running the machine with the base plate off: unless the maker says it is fine, replace the cover before testing.

Care and Upkeep Over Time

Check the roll every month or two if you vacuum often. Cut away hair, empty the bin before it is full and clean or replace filters as the manual describes, because airflow problems can make the motor work harder. Avoid vacuuming cords, string or large items that can jam the roll. Many makers suggest replacing the belt on a regular basis, so look for a schedule in the manual. Keep one spare belt of the right type, labeled with the model, so you are never without.

Glossary

  • Brush roll: the rotating bar with bristles that agitates the carpet.
  • Motor shaft: the small spindle that drives the belt.
  • Belt groove: the channel on the roll where the belt sits.
  • End cap: the part at each end that holds the roll in the base.
  • Glazed: shiny and hard from heat and friction, a sign of wear.
  • Base plate: the cover on the underside of the head.

Safety and Setup Before You Open Anything

A vacuum belt job is one of the friendlier repairs around the house, but it still involves a machine that spins a brush at high speed and connects to a wall outlet. Start by unplugging the vacuum, not just switching it off. If it is a cordless model, remove the battery pack before you touch the brush area. Many uprights have a thermal or motor protection feature that can restart the machine on its own after cooling, so a switch alone is never enough.

Next, give yourself a clear workspace. A kitchen table with a towel or sheet of newspaper on top works well, and it keeps screws and small clips from rolling away. Lay the vacuum on its back or side as the owner manual suggests. Some models need to be tipped fully flat to expose the base plate, and others have a release lever that lets the head pivot. If you no longer have the manual, search the model number on the manufacturer’s website, where a PDF is often free to download.

What to Gather

  • A screwdriver that fits the base plate screws. Many are Phillips, but some brands use Torx or security-style heads, so check before you start.
  • A pair of scissors or a seam ripper for cutting away hair wrapped around the roller.
  • A small flashlight or phone light to see inside the belt chamber.
  • Disposable gloves and a dust mask, because the chamber often holds fine dust, pet dander and old debris.
  • A small container or magnetic tray for screws.
  • The replacement belt, kept in its packaging until the moment you need it.

Take a quick photo of the underside before you unscrew anything. A picture of the belt path and the position of any clips is the cheapest insurance against reassembly mistakes.

Reading the Old Belt for Clues

When you pull the old belt out, do not just toss it. It often tells you why it failed, and that helps you avoid repeating the problem with the new one.

  • A belt that is stretched, loose or shiny on the inner surface has simply worn out over time. This is the most common and least worrying case.
  • A belt that is snapped cleanly in one place suggests age or a sudden jam, such as a sock, cord or toy caught in the brush.
  • A belt with melted spots, glazing or a burnt smell usually points to friction. Something has been holding the brush roll still while the motor kept turning.
  • A belt with one frayed edge or a groove worn on one side suggests misalignment, a bent pulley or a damaged brush housing.
  • A belt that is covered in hair and thread was probably running through a roller wrapped tight with debris.

If the old belt looks fine but the brush is not spinning, the problem may not be the belt at all. A cracked motor pulley, a worn brush roll bearing or a switch fault can all mimic a bad belt. Check those parts before assuming the new belt will fix everything.

Matching the Right Belt Type and Size

Belts look similar but are not interchangeable. The main differences are width, thickness, length, and the shape of the surface. Flat belts, sometimes called round-flat, grip the pulley with a smooth surface, while geared or toothed belts have ribs that mesh with the motor shaft. Using the wrong style can cause slipping, noise or a belt that jumps off the pulley.

The simplest way to match a belt is to use the model number of the vacuum, which is usually on a label on the base, back or underside. Replacement belts are often listed by model or by a letter-and-number code. If you cannot find a code, measure the old belt. Lay it flat, measure its length, then double that figure to estimate the loop length, and measure its width with a ruler. These measurements should still be compared to the product listing, since stretched belts read longer than new ones.

A few buying habits help:

  • Buy from a seller that states which models the belt fits, not just a general size range.
  • Compare the listing’s model list to the exact number on your vacuum, since similar names often hide different parts.
  • Order a pack of two or three if the price is low, because belts are a wear item and you will replace them again.
  • Keep the packaging until the repair works, in case you need to return an incorrect part.

Original manufacturer belts and third-party versions can both work. Cheaper belts may stretch sooner or use a different rubber compound, so look at recent reviews and return policies if you buy aftermarket parts.

Checking the Brush Roll and Housing While You Are There

With the base plate off, you have a rare chance to inspect parts that are normally hidden. A few minutes here can save you a second repair next month.

The Brush Roll

Remove the brush roll and spin it by hand. It should turn smoothly with no grinding or wobble. Cut away any hair or string wrapped around the ends, since that is the most common cause of bearing heat and belt failure. Look at the bristles. If they are worn flat or bent over, the vacuum will clean poorly regardless of how good the belt is, and many brands sell replacement rolls.

The Motor Pulley and Belt Channel

Look at the small pulley on the motor shaft. It should be clean, round and free of cracks. A rough or oily pulley can chew through a belt quickly. Wipe it with a dry cloth, and remove any thread with tweezers. Check the channel where the belt runs to make sure there are no sharp edges, melted plastic or loose screws.

End Caps and Bearings

The end caps hold the brush roll in place. If they are cracked or loose, the roll can tilt and push the belt sideways. Bearings should feel smooth with no gritty resistance. If one feels rough, replace the end cap or the whole roll, depending on what the manufacturer sells.

Time, Cost and When to Stop

For most upright models, a first-time belt swap takes roughly 15 to 45 minutes once the vacuum is on the table, depending on how many screws hold the base plate and how packed the chamber is. Belts are generally inexpensive, and the real cost is usually the time spent finding the correct one. Prices vary by brand and region, so check current listings rather than relying on a single number.

Know when to stop. If the vacuum has a burning smell, smoke, visible damage to the power cord, a cracked housing or a motor that hums without spinning, do not keep experimenting. Unplug it and have it inspected by a qualified repair shop. Likewise, if the machine is old and the repair is approaching the price of a new unit, consider whether the money is better spent on a replacement. For machines still under warranty, check the terms first, because opening the housing may void coverage.

Common Reasons a First Attempt Goes Wrong

Most failed belt swaps come down to a handful of small errors. The belt may be twisted into a figure-eight shape, which makes it slip or squeal. It may sit on only part of the brush roll pulley instead of seated in its groove. A hidden clip on the base plate may not be fully engaged, leaving the roll slightly crooked. Or the brush roll may be seated backward, which matters on models where one end has the drive pulley. If the belt pops off straight away, remove it and start again slowly, checking each of these points in turn.

A Short Checklist for the Finished Repair

Before you plug the vacuum back in, run through a final check. The belt should sit snugly over both the motor pulley and the brush roll, with no twists. The brush roll should spin freely by hand, and the belt should follow it without jumping. The base plate should sit flat and all screws should be tight. Make sure no tools or loose parts remain in the chamber.

Then plug the vacuum in and run it briefly while holding it off the floor, with the brush area pointed away from you and nothing near it. Listen for rubbing, squealing or clicks. If the brush spins evenly, test it on a small patch of carpet. Check again after your first full cleaning session, since a slightly misaligned belt can creep off a pulley within minutes.

Why Belts Fail: Reading the Wear Pattern Before You Blame the Belt

A vacuum belt rarely fails for no reason, and treating every failure as simple old age means the new belt inherits the same problem. Before you fit the replacement, spend a few minutes reading the old belt and the parts around it the way you would read a worn tyre: the pattern of damage usually points at the cause. A belt that has snapped cleanly across its width, with the ends looking frayed and stretched thin just before the break, has usually been overloaded repeatedly — the brush roll was asked to turn against resistance it could not overcome, such as a jammed end bearing, a mat of hair wound tight around the roll, or a height setting pressed so low on thick carpet that the roll could barely rotate. A belt that is glazed — smooth, shiny and hard on its inner face — has been slipping and generating heat instead of gripping, which points to a stretched belt, a worn motor pulley, or oil and polish residue in the belt channel making everything slick.

A belt worn thin on one edge only tells a different story: something is out of alignment. Perhaps the brush roll is not seated squarely in its end caps, one end cap is worn oval, or the roll itself is slightly bent from an earlier impact with a hard object. A belt that has rolled over on itself, so it runs twisted, suggests it was fitted twisted in the first place or that it is the wrong width for the channel and has room to flip. None of these causes is fixed by a fresh belt alone. The fresh belt will track the same way, slip the same way and fail the same way, sometimes within a single cleaning session. So the diagnostic habit is simple: old belt off, look at it under a good light, turn it inside out, flex it, and compare its condition with the state of the roll, the pulley and the channel. Only when the cause is understood does the replacement become a repair rather than a rehearsal for the next failure.

Preparing the Machine and the Work Area Properly

Most belt changes go wrong in the preparation rather than the fitting. Start with the machine unplugged — not merely switched off — and give a cordless model the same respect by removing its battery pack or locking it off as the maker directs. Work on a hard, flat surface at a comfortable height, ideally a table or workbench with a clean towel or old sheet laid down. The towel does three jobs: it stops small screws rolling away, it protects the vacuum’s casing from scratches as you turn the machine over, and it catches the surprising amount of dust and grit that falls out of a base plate the moment it is opened. Lay the screws out in the order you remove them, or drop them into the compartments of an ice-cube tray or a muffin tin; base plates often use screws of two different lengths, and forcing a long screw into a shallow hole can crack the plastic boss behind it.

Photograph the underside before you remove anything, and again once the base plate is off and the old belt is exposed. These two pictures are your routing diagram and your seating diagram in one. Note which way the brush roll sits — many rolls are not symmetrical, and the end with the belt groove belongs at a specific side. Note also any arrows or lettering on the old belt and which way they face. While the machine is open, this is the moment to clean: pull hair and thread from the roll ends with scissors or a seam ripper, working away from the bristles, spin the roll by hand to feel for gritty or stiff bearings, and wipe the belt channel and motor pulley with a dry cloth. A channel lined with rubber dust from the old belt gives the new belt a gritty bed to run in, which shortens its life and can make it squeal.

Deciding whether the brush roll itself needs attention

The belt and the brush roll live or die together. With the belt off, spin the roll between your fingers. It should turn freely and quietly, with no wobble and no grinding. If one end feels stiff, the bearing at that end may be packed with hair that has worked its way inside the end cap; on many models the end caps pull off so you can clear exactly this. Check the bristles too: rows worn down to stubs cannot agitate carpet properly no matter how well the belt drives them, and a roll with melted or flattened patches from a past jam will thump as it turns. If the roll is in poor shape, replacing the belt alone gives you a machine that runs but cleans badly, and the uneven roll will keep stressing belts. Treat the two as a pair when you assess the job.

Fitting the New Belt With Care

The fitting itself is a short sequence, but each step has a detail that matters. Loop the new belt over the motor shaft or pulley first, as the design of your machine dictates, then stretch it over the brush roll groove, using the roll itself as the lever: seat one end of the roll in its housing, hook the belt into the groove, and then ease the other end down into place while holding gentle tension. This order matters because trying to fit the roll first and stretch the belt afterwards usually ends with the belt twisted or half out of its groove. Once the roll is seated, rotate it by hand through several full turns in the direction it normally spins. The belt should settle into the centre of the groove and stay there, neither climbing the edge nor drifting towards one end cap. If it drifts, stop and find out why now, while the base plate is still off — a drift corrected at this stage takes a minute; discovered later, it means opening the machine again.

Refit the base plate without forcing it. If it will not sit flush, something inside is misplaced — a roll end cap not fully home, the belt sitting proud, or a wire or clip out of its channel. Forcing the plate down on top of a misplaced part cracks housings and pinches belts. Start all the screws loosely, check the plate is seated evenly, then snug them up in turn rather than driving one fully home and moving on. Before you stand the machine up, give the roll one last spin by hand through the plate opening if there is one, and confirm nothing scrapes. Only then plug in, switch on briefly on a hard floor, and listen: a healthy drive sounds even and unstrained, with no rhythmic thumping, no high squeal and no smell. A short test run now, with the machine where you can switch it off instantly, is far better than discovering a problem halfway through cleaning a carpeted room.

Troubleshooting by Symptom After the Swap

The burning smell comes back within minutes

Heat and smell mean friction, and friction means something is slipping or something is stalled. Switch off and unplug, then check in order: is the brush roll actually turning freely by hand, or has a bearing seized? Is the belt the correct part — a belt that is too long slips and glazes, and a belt that is too short strains the motor and can drag the roll against the housing? Is the height setting appropriate for the floor, so the roll is not being pressed into deep pile? Work through those three before assuming the new belt is faulty; in practice the belt is usually the messenger, not the culprit.

A squeal or chirp at start-up

A brief chirp as the motor spins up can be a belt bedding in, but a persistent squeal points to slip or contamination. Dust the pulley and groove clean, check the belt is not twisted — a twisted belt presents its edge to the pulley and sings — and make sure no cleaning polish, furniture spray or similar household product has misted into the base during storage, because a light film of anything slippery in the channel defeats the belt’s grip completely.

The roll spins on hard floors but stalls on carpet

This pattern suggests the drive is marginal: the belt grips when the load is light and slips when the carpet resists. Suspect a slightly stretched or incorrect belt, worn pulley surfaces, or a roll whose bearings turn freely unloaded but bind under side pressure. Press the roll ends gently sideways while turning it; roughness that only appears under pressure is the giveaway.

The belt walks off to one side

Tracking problems are alignment problems. Check that both end caps are fully seated and identical in orientation, that the roll is the correct one for the machine and not a near-match, and that no lump of compacted hair at one end is pushing the roll out of square. A roll running even slightly crooked will walk a belt off its groove every time, and no amount of refitting the belt alone will cure it.

A Second Worked Example: The Much-Used Family Upright

Consider a common household case. An upright used daily in a home with two long-haired occupants and a shedding dog begins leaving lines of grit on the carpet and smelling hot. The belt, when the base is opened, has not snapped — it has stretched, glazed and begun to crack, and the brush roll is wound with hair so tightly at both ends that the roll barely turns by hand. The lesson in this example is that the belt is the least of the problems. The repair that actually restores the machine is the full sequence: unplug, photograph, open, cut away every strand from the roll ends, pop the end caps and clear the hair packed inside them, spin-test the roll until it runs freely, wipe the channel and pulley, then fit the correct new belt and hand-turn it to confirm tracking. Skipping straight to the belt would have produced a machine that smelled hot again within the week, because the seized roll ends were the cause and the stretched belt merely the symptom. Worked through in order, the same job takes perhaps ten extra minutes and lasts.

Keeping a Simple Rhythm So Belts Last

Belts last longest in machines that are kept clear. Build the habit of checking the brush roll whenever you empty the bin or change the bag — a thirty-second look catches hair building up at the ends long before it becomes a jam. Keep a note of the belt part number somewhere durable: a photo of the rating plate and the belt packaging on your phone saves guesswork at reorder time and prevents the near-match purchase that causes half the fitting problems described above. Store spare belts flat, away from heat and sunlight, since rubber ages in a hot cupboard almost as fast as it ages in the machine. And treat any change in sound, smell or cleaning performance as information rather than background noise: the machine almost always announces a belt problem in one of those three ways before the belt actually fails, and catching it at the announcement stage turns an emergency into a planned ten-minute job.

Bagged, Bagless and Cylinder Machines: Small Differences That Matter

The belt change follows the same logic on most machines, but the details shift with the design. Traditional uprights usually hide the belt under a base plate, as described above. Many bagless uprights route the belt at one side of the roll, behind a cover that also carries a washable pre-motor filter nearby — worth a rinse and a full dry while you are there, following the maker’s directions, since a choked filter makes the whole machine feel weak and can be mistaken for a drive problem. Cylinder and canister machines with a powered floor head have their belt inside the head rather than the body; the head is lighter to handle but its screws are smaller and its wiring runs close to the belt channel, so work slowly and never pull the head apart by force. Some heads use a geared or toothed belt that rarely stretches but can jump teeth if the roll jams hard; if a toothed belt looks intact yet the roll stutters, count that possibility before replacing parts. Stick and robot vacuums mostly use direct-drive or geared rolls with no user belt at all — if yours has no belt listed in its manual, do not go hunting for one; the equivalent maintenance there is clearing the roll ends and checking the drive wheels.

Whatever the design, two habits transfer across all of them. First, the manual’s diagram outranks any general guide, including this one, whenever they differ — makers vary the routing in ways that are not obvious from outside. Second, finish every job with the same closing checks: roll spins freely by hand, belt tracks centrally, plate or cover seated without force, screws snug but not strained, and a brief supervised test run on a hard floor before you tackle carpet. Those five checks take under a minute and catch nearly every fitting mistake at the moment it is cheapest to fix.

A note on keeping the old belt as a reference

Until the new belt has survived a few full cleaning sessions, keep the old one rather than binning it straight away. If the replacement fails early, comparing the two side by side — length laid in a circle, width, thickness, any printing — is the fastest way to spot a near-match part that was sold as the correct one. Once the new belt has proved itself, the old one can go, and the packaging of the new belt is worth keeping in a drawer: it carries the exact part reference that makes the next reorder a certainty rather than a search.

Finally, jot down the date of the change on that packaging or in a note on your phone. Belt life is easier to judge with a date attached: a belt that lasted two years of weekly use has simply worn out, while a belt that failed after two months is telling you something else in the machine needs attention. That single habit — recording the date — turns the next belt change from guesswork into a decision based on how your machine actually behaves in your home, and it costs nothing but a few seconds each time you do the job.

FAQ

How do I know which way the belt goes?

Take a photo before removing it. The belt rides on the brush roll groove and the motor shaft, and a photo makes it easy to copy.

Why does the new belt keep slipping off?

Usually the roll is not seated in its end caps, or hair is still bunched near the bearings. Clean the ends and refit the roll.

How often should the belt be replaced?

It varies with use and model. Check the manual for a recommended interval, and replace the belt sooner if it looks stretched or cracked.

Can I use a belt from a different model that looks the same?

Not safely to assume. Small differences in length and width affect grip and motor load. Use the part the maker lists for your model.

Is the job the same for a robot vacuum?

Not always, as many have no belt or a different drive. Follow the maker’s manual for your model.

Do I need special tools to change a vacuum belt?

Usually not. Most models need a screwdriver for the base plate, scissors for cutting hair, and a light. Some brands use Torx or security screws, so check the heads first. If you cannot get the plate off, look up the model manual before forcing anything.

How long does it take to replace a vacuum belt?

A first attempt commonly takes around 15 to 45 minutes, depending on the number of screws and how packed the belt chamber is. Having the right belt, a clear workspace and a photo of the original layout makes the job faster and less frustrating.

Why does my vacuum smell like burning rubber?

A burning smell often means the brush roll is jammed or wrapped with hair and the belt is slipping against it. Unplug the vacuum, clear the roll, and inspect the belt. If the smell continues, or you see smoke, stop using it and have a repair shop check the motor.

Can I clean the brush roll without removing it?

You can cut loose hair along the roll using scissors, but removing it is better. Taking it out lets you clear hair from the ends and bearings, spin it to check for roughness, and see the belt channel. Always unplug the machine before doing either.

Is a cheap aftermarket belt as good as the original?

It can be, but quality varies. Some third-party belts match the original closely, while others stretch quickly or fit loosely. Check that the listing names your exact model, read recent reviews, and keep the packaging in case you need to return it.

Can I keep using the vacuum if the belt is stretched but not broken?

You can, but it is a false economy. A stretched belt slips under load, so the brush roll turns slowly exactly when the carpet needs it most, cleaning performance drops, and the slipping generates heat that ages the belt further and can leave a hot rubber smell in the room. The machine will also tend to leave debris in lines where the roll was barely turning. Replacing a stretched belt promptly restores the drive and protects the motor from the extra strain of pushing a slipping, dragging roll.

Should I replace the belt and the brush roll at the same time?

Only if both need it. Inspect each on its own merits: the belt for stretch, cracks, glazing and edge wear; the roll for free-spinning bearings, sound bristles and a straight shaft. A good roll does not need replacing because the belt failed, and a good belt should not be sacrificed to a roll with seized ends. The exception is convenience — if the roll is clearly near the end of its life and you already have the machine open, doing both in one session saves opening it twice.

Why did the new belt feel much tighter than the old one?

Because the old one had stretched. Rubber belts lengthen gradually in service, so a correct new belt often feels surprisingly snug by comparison, and fitting it takes the firm, steady pull described in the fitting section. That snugness is normal and is what restores grip. What is not normal is a belt that cannot be fitted at all without extreme force, or one that makes the roll hard to turn by hand once fitted — that suggests the wrong part, and it is worth double-checking the part number before running the machine.

Does the direction the belt faces matter?

On many belts, no — they are plain loops. Where a belt has printed lettering or arrows, fitting it so the print reads as the maker intended is a good habit, and some toothed or ribbed designs do have a correct orientation. The reliable rule is to match what your pre-removal photo shows: same routing, same face outwards, same seating in the groove. When in doubt, the manual for your model settles it.

My vacuum has two belts. Do I change both?

Some designs use a second belt or a geared arrangement linking parts of the drive. If your machine has more than one, inspect all of them while the base is open, because they age together and the surviving old belt often fails soon after its partner is renewed — leaving you to open the machine again. Replace any that show stretch, cracking or glazing, and photograph the routing of each before removal, since multi-belt layouts are the easiest to reassemble incorrectly.

How do I dispose of the old belt and the debris from the base?

The old belt and the hair and grit cleared from the roll go in the ordinary household waste; there is nothing hazardous in them. It is worth wiping out the inside of the base plate before refitting it, so the dust you disturbed does not blow straight back through the machine on its first run. If the old belt snapped and a piece is missing, look for it inside the housing — a stray fragment left in the channel can foul the new belt.

The Short Version

Unplug first, open the base, clear the roll, then loop the matching belt over the shaft and the roll. Follow the maker’s manual, and leave cord or motor faults to a qualified professional.