A bench dog is a peg that drops into a round hole in a workbench top and acts as a stop or as one jaw of a clamp. Most modern sets are made for 3/4 inch (19 mm) holes, the size also used on many portable bench tables. The main choices are the material, the count, whether the dog is a plain stop or a clamp, and what the contact pad is made of.
The six sets below cover plain nylon and aluminum stops, a parallel clamp dog set and three clamp styles. Sizes, counts and materials come from each listing page and are the makers’ own claims. We have not used these products ourselves. Where a listing disagrees with itself or uses an odd unit, we say so.
As an Amazon Associate we earn from qualifying purchases. Links below are affiliate links, and they do not change the product information we give.
What to Look For
| Feature | Why it matters |
|---|---|
| Hole size | Most sets fit 3/4 inch (19 mm) holes; a few fit 20 mm |
| Material | Aluminum is hard wearing; nylon is gentler on the work |
| Stop or clamp | A plain dog stops a board; a clamp dog also presses it |
| Pads | Rubber, EVA or silicone pads protect the surface |
| Count | Two per clamp setup, more for long boards |
In this guide
Specs at a Glance
| Set | Count and material | Type | Notes |
|---|---|---|---|
| POWERTEC 71188-P3 | 12; nylon | Stop | EVA bench brake inserts; 3/4 in holes |
| JET 70402 | 4; aluminum | Stop for parallel clamps | Converts to 11/16 in length for 3/4 in stock; 12 oz |
| ViewReal 6-pack | 6; anodized aluminum | Stop | Non-slip pads; 19 mm; fits MFT tables per the maker |
| BGASNW 8 pack | 2 clamps, 4 dogs, 2 wrenches; stainless steel | Clamp set | Horizontal and vertical force; silicone pads |
| HAUTMEC HT0276 | 2 clamps; PA6/GF30 and rubber | Clamp | 170 lb listed; quick-release lever |
| POWERTEC 72105 | 2 clamps; plastic | Clamp | 176 lb listed; holds stock up to 1-3/16 in thick |
The 6 Best Bench Dogs

Top pickBest for a bench with many dog holes
1. POWERTEC 12PCs Bench Dogs for 3/4 in Dog Holes (71188-P3)
Twelve nylon bench dogs, each about 0.75 inch in diameter and 1.88 inches tall, with removable EVA inserts that the maker calls bench brakes. The squared pad has two 3/16 inch holes for dowels. The color varies between orange and black. The maker says they are low profile and non-marring.
Suits: a bench with many dog holes. Strengths: twelve dogs and soft inserts. Weaknesses: plastic is less rigid than metal. Skip it if you want a clamp.

Best for parallel clamp users
2. JET Parallel Clamp Bench Dogs (70402)
Four aluminum dogs listed at 12 ounces for the set, made to work with parallel clamps. The maker says they convert to an 11/16 inch length to suit 3/4 inch material, and a limited lifetime warranty is mentioned. The listing gives little else, so check the fit with your own clamps.
Suits: parallel clamp users. Strengths: aluminum and a warranty. Weaknesses: sparse details. Skip it if you want a ready clamp.

Best for planing and sanding stops
3. ViewReal 6-Pack Aluminum Alloy Bench Dogs
Six red anodized aluminum dogs with non-slip pads for 3/4 inch (19 mm) holes. The maker says they sit below the level of the work so they do not interfere with planer blades and that they drop into MFT style tables. The listed weight is 1.16 ounces, which seems low for six, so check it on arrival.
Suits: planing and sanding stops. Strengths: hard aluminum and six pieces. Weaknesses: no clamping action. Skip it if you want force from the dog.

Best for holding panels down and in
4. BGASNW Bench Dogs Clamp Set, 8 Pack
A kit of two bench dog clamps, four bench dogs and two ratchet wrenches in stainless steel with silicone pads, for 0.75 inch holes. The maker says it gives force in horizontal and vertical directions. The table shows a tensile strength of 150 psi, which is not a clamping force in pounds, so there is no comparable load figure.
Suits: holding panels down and in. Strengths: clamps and dogs in one kit. Weaknesses: an odd force unit. Skip it if you need a stated load in pounds.

View Bench Dogs Clamp Set for 3/4 Inch (19mm) Workbench Dog Holes, 8 Pack on Amazon

Best for glue-ups and sanding
5. HAUTMEC 3/4 in Bench Dog Clamp, 2 Pack (HT0276)
Two quick-release clamps with a pull-down lever, alloy steel rods, PA6/GF30 nylon bodies and soft rubber pads. The maker lists up to 170 pounds (750 N) of force and says the screw-free design leaves no burrs. They fit 19 mm holes.
Suits: glue-ups and sanding. Strengths: a fast lever and a stated force. Weaknesses: nylon bodies. Skip it if you want an all-metal clamp.

Best for thin to medium stock
6. POWERTEC Bench Dog Clamps for 3/4 in Dog Holes (72105)
Two quick-release plastic clamps for 3/4 inch holes with a listed clamping force of up to 176 pounds. The maker says they hold workpieces up to 1-3/16 inches thick and work with bench cookies and other accessories, and that they are not recommended for CNC machines.
Suits: thin to medium stock. Strengths: a clear thickness limit. Weaknesses: only two pieces. Skip it if you clamp thicker boards.
Care and Setup
- Check the hole diameter first, since 3/4 inch and 20 mm are close but not the same.
- Keep the dog below the top of the work if you plan to plane across it.
- Wipe glue from pads before it dries.
- Follow the maker’s listed load and thickness limits.
Mistakes to Avoid
- Buying dogs for a hole size your bench does not have.
- Comparing force figures that use different units.
- Expecting a plain stop to hold a board by itself.
- Letting a metal dog stand above the work during planing.
Hole Fit, Tolerance and Wobble
A bench dog only works as well as it fits its hole. The ideal fit is snug enough that the peg does not wobble or tilt under pressure, yet loose enough that you can drop it in and pull it out by hand. In practice, holes drilled by different people or machines vary a little, and so do the pegs. That is why two products that both claim to fit a given size can behave differently in the same bench.
Start by measuring your holes with calipers, a drill bit gauge or a set of known-size rods, rather than trusting a nominal number. Measure at several points, because a hole can be slightly oval or taper as it goes down. If you drilled the holes yourself with a spade or Forstner bit, they may be a touch larger than the bit size. Measure the dog’s shaft in the same way, and compare the two.
Several things can make a dog wobble. A hole that is slightly too big lets the peg rock, which reduces holding power and can mar the work. A dog with a thin shaft and a tall head gives more leverage to any side force, so it tends to tilt. Some designs add a spring or a friction element to reduce movement, and some rely on a tight fit alone. If you plan to apply strong sideways pressure, look for a design that grips the hole or that comes with a locking feature.
- Check both metric and imperial sizes, since they are close but not identical.
- Test a dog in several holes, not just one.
- If a dog is too tight, lightly sand the shaft or the hole edge rather than forcing it.
- If it is too loose, consider a wrap of tape or a different dog.
Material Choices and Protecting Your Work
Dogs come in several materials, and each has its own strengths. Metal dogs, such as steel, brass and aluminum, are rigid and durable. They resist deformation under pressure but can dent or mar softer workpieces if they contact them directly. Brass is softer than steel and gentler on wood, but it can still leave marks. Aluminum is light and affordable but can wear or bend with heavy use.
Plastic and nylon dogs are lighter and kinder to the surface of the work, and they will not damage a cutting edge if a plane or a saw touches them by accident. The trade-off is lower rigidity, so they can flex or compress under heavy pressure. For light work such as sanding, routing or assembly, a plastic dog is often enough. For heavy planing or edge work, a metal dog may feel more secure.
Many dogs come with pads or inserts made of rubber, silicone or foam. These add friction and protect the workpiece from marks, but they can wear out or collect dirt, which reduces grip. Check whether the pads can be replaced, and keep them clean. If you work with finished pieces, softwood or delicate veneers, consider a dog with a soft contact surface.
Think about your tools. If you plane across the dog, keep the top of the dog below the work surface, so the blade never touches metal. Wooden dogs that you make yourself are an option for this reason, because a mistake leaves a nick in the dog, not the plane. If you work with an edge tool, check the height of the dog before every pass.
Stops, Clamps and Typical Workholding Setups
Dogs are most useful when you understand how they combine with the rest of the bench. A simple stop is a dog that stands in a hole and gives the board something to push against. A second dog in an end vise or a tail vise lets you clamp a board between two points, which holds it flat without a clamp on top of the surface. This setup is common for planing and sanding, because nothing sits in the way of the tool.
Clamp-style dogs add pressure, which lets you hold work down or sideways without a separate clamp. They are handy for glue-ups, edge work and small pieces that tend to slide. Check how the clamp operates, and whether it applies force toward the hole or away from it. Some push against a second dog, some press the work into the bench and some do both.
A few common setups show how the pieces work together.
- Planing a board: place a stop dog at the end of the board and apply force toward it as you push the plane.
- Holding a wide panel: use dogs on opposite sides with a clamp or vise between them to hold the panel in place.
- Edge work: clamp the piece against a dog and a stop to hold it on its edge.
- Sanding or routing: use dogs with pads to keep the work from moving, but check clearance for the tool.
Whatever the setup, never rely on friction alone for heavy cuts. A stop only resists force in one direction, so check that the force on the work pushes it into the stop and not away. Where the force could lift or twist the workpiece, add a clamp or a different hold. If your bench has a grid of holes, plan your layout so you can place dogs where you need them, and leave room for hands and tools.
Adding or Adjusting Dog Holes in Your Bench
If you are buying dogs for a bench that has no holes, or holes in the wrong places, you will need to drill your own. This is a one-time job that rewards care. The goal is a row or grid of holes that are straight, square to the top and the correct diameter. A hole that leans, even slightly, will make the dog tilt and will wear the edges.
The best tool for accurate holes is a drill press, but most benches are too large for that. A portable guide or a drilling jig helps to keep the bit square. Some woodworkers make a simple jig from a block with a guide hole. Others use a hand drill with a square held against the bit. Test the process on scrap wood of the same thickness as your top before drilling the bench.
Choose the spacing based on your work. Closer holes give you more positions but weaken the top a little if overdone. Keep the holes away from the edges, joints and any hardware. Mark the layout carefully with a square and a ruler, and double-check before you drill. Use a sharp bit and go slowly to avoid tear-out on the underside. A piece of scrap beneath the bench top, or drilling from both sides, can help.
Finally, finish the holes. Break the edge with fine sandpaper so the dog slides in without catching, and wipe out dust. A thin coat of wax inside the hole helps the dog move smoothly. Check the fit with your chosen dog before drilling more holes.
Wear, Damage and When to Replace a Dog
Bench dogs are simple parts, but they take a lot of abuse. Regular checks keep them safe and effective. Look for cracks in plastic bodies, bent shafts, rounded edges, worn pads and rust on steel parts. Pay attention to the clamp mechanism on clamp-style dogs. Levers, screws and pivots should move smoothly and hold their position. If a lever feels loose or a screw is stripped, the dog may slip under load.
Clean glue and dust from the pads and the shaft, because buildup affects both grip and fit. Dried glue can be scraped off or softened with a damp cloth if the maker allows. Wipe metal parts and add a light coat of oil if they are prone to rust. Keep the dogs in a tray or a drawer where they will not be knocked about or lost, and store them away from damp.
Replace a dog when it no longer fits snugly, when a pad no longer grips, or when any part is cracked or bent. A damaged dog can fail unexpectedly, and a sudden slip can ruin the work or injure your hand. Because dogs are small and relatively simple, it is better to replace one than to improvise a repair that cannot be trusted.
When you buy, ask these questions. Does the listing give the hole size clearly and in both units? Are pads replaceable? Is the maker’s stated holding limit given in a clear unit? Will it fit the thickness of your bench top? Choose a set that fits your work, and avoid mixing dog types and sizes unless you have tested them in your bench.
What should you check before buying bench dogs, and who should skip each set?
Check your hole size, the type of work you do and the material before you buy bench dogs. A set that does not match your holes will wobble, and a set that does not match your work will sit in a drawer.
- Hole diameter: measure your holes and compare them with the listing, since three-quarter inch and metric sizes are close but not identical.
- Stop or clamp: decide whether you need something to push against or something that presses the work.
- Count: a clamp setup needs a pair, while long boards or many holes call for more pieces.
- Material and pads: consider whether nylon, aluminum or stainless steel suits your tools and workpieces.
- Clearance: if you plane across the dog, check that it sits below the work.
- Returns and warranty: confirm the terms on the listing, and read the maker’s limits for thickness and force.
Now the honest objections. Plastic bodies are kinder to tools but less rigid, and listed force figures come from the makers, so they are not directly comparable. Some listings are sparse, such as the JET, so check the fit with your own clamps.
Skip the plain stop sets, the POWERTEC 71188-P3 and the ViewReal, if you want pressure from the dog itself. Skip the clamp sets if your bench holes are not the stated size or if you clamp stock thicker than the listing allows, which matters for the POWERTEC 72105. Skip dogs altogether if your bench has no holes and you do not want to drill any.
Which bench dogs should you buy?
Choose by the job you do most, then by material and count. Here is how the six sets in this guide map to common needs.
- If you have a bench with many holes and want soft inserts, go for the POWERTEC 71188-P3.
- If you use parallel clamps and want aluminum with a warranty, choose the JET 70402.
- If you want hard-wearing aluminum stops for planing and sanding, choose the ViewReal 6-pack.
- If you want clamps and dogs in one kit, choose the BGASNW 8 pack.
- If you want a quick-release pair with a stated force, choose the HAUTMEC HT0276.
- If you work with thin to medium stock and want a clear thickness limit, choose the POWERTEC 72105.
Many woodworkers end up with one set of plain stops and one pair of clamps, because the two do different jobs. If you must start with one, pick the type that matches your most common task.
Compare the picks above, check the current listing for hole size and what is included, then choose the set that fits your bench and how you work.
Reading the Six Sets Side by Side
The six sets above solve the same basic problem — giving a workpiece something solid to push against — but they differ in how they grip, how tall they sit, and how much of your bench system they assume you already own. Reading them side by side is more useful than reading them one at a time, because the right choice usually comes down to two or three practical trade-offs rather than a single winner.
POWERTEC 12-piece set versus ViewReal 6-pack
These two are the closest match in the list. Both are simple drop-in dogs rather than clamping dogs, so both rely on the workpiece being pushed or planed against them. The POWERTEC set gives you more pieces, which matters if you work on wide panels: four dogs along one edge spread the load and stop a panel from pivoting around a single point. The ViewReal aluminum set gives you fewer pieces but in metal, which resists the slow denting that repeated mallet taps and clamp pressure can cause in softer materials. If you mostly register narrow boards against one or two dogs, the smaller set is enough. If you batch-plane panels or glue-ups, the larger count earns its place in the drawer.
JET parallel clamp dogs versus POWERTEC bench dog clamps
Both of these turn a dog hole into an active clamping point, but they assume different kits. The JET dogs are designed to work with parallel clamps you likely already own, converting them into bench-level clamping without a dedicated vise. The POWERTEC clamps integrate the clamping action into the dog itself, which is quicker to set up for one-off jobs but adds another mechanism to keep clean of dust and glue. Choose the JET route if parallel clamps are already central to your work; choose the integrated clamps if you want a self-contained setup you can drop in, tighten, and remove in seconds.
BGASNW 8-pack versus HAUTMEC 2-pack
The BGASNW set is a quantity play: enough dogs to leave a working layout in place across several holes while you move between operations. The HAUTMEC pair is the opposite philosophy — a small number of clamp-style dogs for targeted holding, such as securing a board for routing or sanding where a plain stop is not enough. Many benches end up with both styles eventually: plain dogs living semi-permanently in the front row of holes, and a clamping pair that comes out only when a stop alone will not hold the work.
Your First Session: Setting Up in the Right Order
Bench dogs reward a calm first session. Start by cleaning out every dog hole you plan to use. Packed dust and old glue change the effective diameter of a hole, and a dog that feels loose on day one is often just sitting on debris. A bottle brush or a blast of air clears most holes; a dog that still wobbles after cleaning is telling you something real about fit.
Next, drop your dogs in and check height above the bench top with the actual stock you plane most often. Dogs should sit below the surface of thin stock so a plane iron never meets them, yet high enough that the work cannot ride up and over under pressure. Test with your thinnest regular board, not with the thickest. Then do a dry planing pass on scrap: push the board against the dogs, take a few strokes, and watch whether the far end creeps sideways. Creep means the dogs are not sharing the load evenly — add a dog, or move one hole closer to the end of the board.
Finally, mark your most-used hole positions lightly in pencil on the bench apron. It sounds trivial, but a repeatable layout saves minutes on every session and stops the random hole-hopping that leads to uneven wear across the bench top.
Technique: Getting More From Plain Stops
A plain bench dog is a stop, not a clamp, and good technique treats it that way. When planing, let the dog take the thrust and use your free hand to keep the board down and registered, rather than trying to pin it with downward force alone. When sanding with a random orbit sander, the tool’s rotation tries to walk the workpiece in a circle; a dog at the corner, paired with a second dog along the edge, resists that rotation far better than a single dog in the middle of one side.
For routing small parts, dogs alone are rarely enough — combine them with a clamping dog or a holdfast so the part cannot lift or spin if the bit catches. For glue-ups, dogs make excellent registration points for keeping panel edges aligned while clamps supply the squeeze; just keep glue squeeze-out off the pads, because dried glue on a pad prints straight into the next workpiece.
Troubleshooting in Diagnostic Order
When workholding with dogs goes wrong, check causes in this order, cheapest and most common first. First, cleanliness: brush out the holes and wipe the dog shafts, then retest. Second, fit: try the same dog in a different hole. If it is snug elsewhere, that one hole has worn oversize; if it is loose everywhere, the dog itself is undersize or worn. Third, layout: a single dog placed near one end of a long board lets the other end swing — add a second point of contact before blaming the hardware. Fourth, technique: excessive downward planing force lifts the tail of a board over a low dog, which looks like a dog failure but is really a pressure problem. Only after those four checks should you conclude a set is wrong for your bench and needs replacing or supplementing.
Care, Storage and Bench Manners
Dogs live a hard life around glue, finish and steel tools. Wipe glue off pads the same day, while it is still soft; dried glue needs picking off and risks tearing pad material. Store loose dogs in a divided box or a drilled block rather than a loose drawer jumble — aluminum edges and plastic pads both suffer in a rattle drawer, and a full set stays a full set only if the pieces come home. Once in a while, run a dog through every hole in the bench as a fit audit: holes near the vise and the front edge wear fastest, and catching an oversize hole early lets you plan around it instead of discovering it mid-glue-up.
Choosing by the Work You Actually Do
If you hand-plane boards most days, prioritise low profile and a snug fit, and take the larger plain set so layout options stay open. If you mostly sand, route and assemble, clamping dogs earn their keep and a smaller count is fine. If your bench is a multifunction table with a grid of holes, quantity matters more than clamping force, because the grid itself becomes your workholding system. And if you are equipping a first bench, start with one plain set and one clamping pair: that combination covers the great majority of tasks, and you will learn your own bench’s habits before spending on duplicates.
Can I leave bench dogs in the holes permanently?
You can, and many woodworkers leave a front row in place. Just check them before planing thin stock, because a dog left sitting slightly high after being knocked is exactly the one a plane iron finds. A quick fingertip sweep across the tops before you start becomes a reliable habit.
What if my bench has no dog holes yet?
Start with the holes your vise and work pattern actually need — usually a row in line with the vise jaws — rather than drilling a full grid on day one. You can always add holes; you cannot undrill them. Match the drill to the dog size you have chosen, test in scrap of the same thickness first, and keep holes clear of the bench’s internal structure.
Workholding Scenarios, Walked Through
Abstract advice becomes useful when it is tied to real jobs. Consider planing a wide glued-up panel flat. A single dog at one corner lets the panel rotate as the plane’s thrust shifts; four plain dogs along the front edge, with the panel also registered against a planing stop or a second row, turn the job into pure planing with no chasing the work around the bench. The lesson generalises: the wider the work, the more contact points it deserves, and the time spent placing dogs is repaid in strokes that all go into cutting rather than correcting.
Now consider sanding a small box or a drawer side. The piece is too small to clamp conveniently and too light to stay put on its own. Two dogs forming a corner — one along each of two adjacent edges — create a pocket the sander’s rotation pushes the piece into rather than out of. Add a non-slip mat under the piece and the setup holds for the whole grit sequence without a single clamp. For routing a small part, escalate: a corner pocket plus one clamping dog, because a router bit that catches can lift work in a way a sander never will, and the clamping dog is the insurance.
Finally, consider a glue-up of a frame or a small carcass. Dogs cannot supply squeeze, and pretending otherwise leads to weak joints, but they excel at registration: dogs set along one edge keep members aligned while clamps close the joints, and they stop the whole assembly skating across a glue-slick bench. Use them as the bench’s memory of where things belong, and let clamps do the squeezing.
Pairing Dogs With the Rest of the Bench
Bench dogs rarely work alone, and understanding their partners prevents duplicate purchases. A face vise with a dog in its jaw turns the bench into a long clamp for boards — the classic arrangement for planing edges and faces of stock too long for stops alone. A tail vise does the same job built-in. Holdfasts complement dogs when work needs downward pressure rather than end pressure: dogs stop the piece sliding, the holdfast stops it lifting. Planing stops — a thin batten hooked or screwed at the bench end — suit very thin stock that would ride over any dog. Knowing which device supplies which direction of force lets a small kit cover a large range: dogs for thrust, holdfasts for lift, vises for squeeze, stops for the thinnest work.
A Pre-Purchase Fit Checklist
Before ordering any set in this list, run four checks on your own bench. One: measure your holes at several points with the dogs’ specified size in mind — holes vary across a bench, especially a well-used one. Two: measure your bench top’s thickness and your thinnest regular stock, and compare both against dog height; the dog must disappear below thin stock yet still register against thick stock. Three: decide honestly how many working positions you use, because that number — not the biggest set on the page — should set the piece count you buy. Four: check what your vise offers; a vise jaw dog can change which set makes sense, since one row of holes may already be covered. Ten minutes with a tape and a notebook prevents the most common bench dog disappointment, which is not quality but simple mismatch.
Building Bench Dogs Into Your Everyday Workflow
The difference between a set of dogs that transforms a bench and a set that gathers dust is routine. Woodworkers who benefit most keep a default layout in place — a working row of holes populated and ready — so that using dogs costs no setup thought at all. The board arrives, it registers against the dogs, and work begins. Special layouts get built for special jobs and dismantled afterwards, but the default layout is the one that pays rent every single day. If your dogs live in a drawer and require a decision before every use, they will lose to whatever clamp happens to be nearest, regardless of merit.
Pair that routine with a quick end-of-session habit: dogs wiped, pads checked for glue, pieces counted back into their block or box. Sets stay complete, pads stay clean, and the next session starts at full strength. It takes under a minute, and it is the entire maintenance programme for one of the hardest-working accessories on the bench.
Do bench dogs work for left-handed setups?
Yes — dogs are among the most handedness-neutral accessories in the shop, because holes and layouts mirror freely. Set your working row to suit your stance and your vise position, and every technique in this guide applies unchanged. The only adjustment worth making is keeping your most-used holes on the side your body actually works from, so you are never reaching across the bench to register a board.
What is the smallest useful set to start with?
Four plain dogs cover the core layout for most benches — two to register an edge, four to control a panel — and adding one clamping pair extends the system to routing and sanding security. That starter combination handles the great majority of tasks in this guide; expand only when a specific job has shown you the gap, because a gap you have felt is a reliable guide and a gap you have imagined usually is not.
How do I stop a board creeping sideways during a long planing session?
Sideways creep means the thrust is not the only force in play: the plane is being angled slightly, or the board’s edge against the dogs is not straight, so each stroke walks the work along the row. Check the board’s edge first — a bowed edge contacts only one dog and pivots around it. Then add a second contact point along the side edge, even a single dog in a side hole, to kill the rotation. Finally, review your stroke: a plane pushed with a subtle diagonal bias will walk any board that is free to move, and correcting the stroke fixes creep on every future setup, not just this one.
When should I replace a set of bench dogs rather than work around it?
Replace when the problem follows the dogs rather than the bench: shafts worn visibly undersize, pads torn or hardened so they no longer grip or protect, or clamping mechanisms that slip under moderate load after cleaning. A set that fails those tests costs you a small amount of accuracy on every job, which is far more expensive over a year than a replacement set. Keep the best survivors of the old set as spares for low-stakes layouts — worn dogs still serve as extra registration points even after they retire from precision duty.
How should I arrange dogs for planing thin stock?
Thin stock is the bench dog’s hardest test, because the board wants to flex, ride up and chatter all at once. Keep the dogs low — their tops safely below the board’s surface — and increase the number of contact points rather than their height: three or four low dogs along the edge share the thrust without ever threatening the plane iron. Back the arrangement with a planing stop or a thin batten at the far end if the board still creeps, and plane with lighter, faster strokes that skim rather than shove. If a board is so thin that no dog can register against its edge, that is the batten’s job entirely — recognising the handover point between the two systems is part of bench craft, and forcing dogs below their working thickness helps neither the board nor the bench.
A last word on mixing dog types on one bench
Most mature benches end up mixed: plain dogs living in the front row, a clamping pair in the drawer, perhaps a taller set kept for thick work. That mixture is not indecision — it is the bench’s vocabulary growing to match the work’s sentences. Add types only when a real job has exposed a real gap, label nothing, organise by reach rather than by brand, and let the layout evolve. The test of the system is invisible: work gets held, quickly and without thought, and your attention stays where it belongs, on the cut, the surface and the fit. When holding disappears from your awareness entirely, the dogs — whichever sets you chose — have done everything this guide asked of them.
Bench Dog FAQ
What is the difference between a bench dog and a bench dog clamp?
A plain dog is a stop that a board pushes against. A clamp dog has a lever or screw that presses the board against another dog or the bench.
Which set has the most pieces?
The POWERTEC 71188-P3 lists twelve dogs. The ViewReal lists six and the BGASNW kit lists two clamps, four dogs and two wrenches.
How snug should a bench dog be in its hole?
It should drop in and lift out by hand without wobbling. If it rocks, the hole is too big or the shaft too small. If it needs force, ease the fit by sanding lightly.
Are plastic dogs strong enough?
For light work such as sanding, routing and assembly, they often are. For heavy planing or strong clamping, metal dogs may feel more secure. Follow the maker's listed limits.
Why does my dog tilt when I apply force?
The hole may be oversized or not square, or the dog may have a thin shaft with a tall head. Check the fit, and consider a design with a locking or friction feature.
Can I make my own bench dogs?
Yes, many woodworkers make them from hardwood, which is gentle on tools and workpieces. Match the shaft to the hole and keep the top below the work surface when planing.
How far apart should I space dog holes?
There is no single rule. Closer spacing gives more flexibility but can weaken the top if overdone. Plan around the work you do and keep holes away from edges and joints.
What is the best way to drill straight holes?
Use a drill press if possible, or a drilling guide or jig that keeps the bit square. Practice on scrap of the same thickness first.
How do I clean glue off dog pads?
Let it dry and scrape it off gently, or soften it with a damp cloth if the pad material allows. Check the maker's care notes before using any solvent.
What size holes do most bench dogs fit?
Most modern sets are made for three-quarter inch holes, which is about 19 mm. A few are listed for 20 mm. Measure your own holes before buying, since close sizes can still wobble.
Do I need bench dogs if I already have a vise?
Not necessarily, but they add flexibility. Dogs let you hold boards flat for planing and sanding without clamps in the way. If you already have holes in your bench, they are a low-effort addition.
Can bench dogs be used on a portable workbench?
Often yes, if the table has matching round holes. Several listings mention portable tables and MFT-style tops. Check the hole size and the maker's notes before ordering.
Are aluminum bench dogs better than nylon ones?
Neither is better for every job. Aluminum is more rigid and hard wearing, while nylon is gentler on the work and on tool edges. Choose by whether you value rigidity or surface protection.
How many bench dogs do I need?
Two will cover a basic clamp or stop setup, and more help with long boards or wide panels. Many people start with a small set and add more as their work demands. Check the count on the listing.
Will bench dogs damage my workbench holes?
A well-fitting dog should not. Forcing a tight dog or letting a loose one rock can wear the hole edges over time. Break the hole edge lightly and keep the fit snug but easy.
The Short Version
For twelve soft-pad stops, the POWERTEC 71188-P3. For parallel clamp work, the JET. For six aluminum stops, the ViewReal. For a clamp and dog kit, the BGASNW. For a quick-release pair with a stated force, the HAUTMEC. For a listed thickness limit, the POWERTEC 72105.







