A try square checks and marks right angles. A blade sits in a stock, and the stock rides along an edge so you can scribe a line across the board or check that a corner is square. The main choices are the blade length, the handle material, the scale and whether the square adds a level or a scribe.
The six squares below run from a 6 inch steel engineer’s square to a 10 inch aluminum handled square with a bubble level. Sizes, materials and features come from each listing page and are the makers’ own claims. We have not used these squares ourselves, and no listing here gives a measured accuracy figure we could compare. Where a listing disagrees with itself, we say so.
As an Amazon Associate we earn from qualifying purchases. Links below are affiliate links, and they do not change the product information we give.
What to Look For
| Feature | Why it matters |
|---|---|
| Blade length | A longer blade reaches across wider boards |
| Handle | Hardwood, bamboo, aluminum or steel change the feel and weight |
| Scale | Etched marks in 1/16 or 1/8 inch help quick layout |
| Extras | Levels, scribes and kickstands add uses but also parts |
In this guide
Specs at a Glance
| Square | Blade and handle | Scale | Notes |
|---|---|---|---|
| Johnson 1940-0800 | 8 in stainless; carbonized bamboo | 1/8 and 1/16 in | 6.08 oz; limited lifetime warranty |
| Arrow 10 in | 10 in stainless; aluminum alloy | 1/16 in, metric and SAE | Bubble level, brass scribe, 45 degree face |
| Swanson TS152 | 8 in stainless; hardwood, brass bound | 1/16 and 1/8 in | 7.36 oz; fixed 90 degree seat |
| Swanson SVR149 | 9 in stainless; aluminum with rubber insert | 1/16 in | Retractable kickstand; scribe bar |
| Spear and Jackson CTS9 | Spring steel; hardwood and brass | Not listed | Listing sizes conflict with the 9 in name |
| Faithfull 150mm | 6 in hardened steel | Not listed | Blade 1.7 mm; ground surfaces |
The 6 Best Try Squares

Top pickBest for a light everyday square
1. Johnson 1940-0800 Carbonized Bamboo Try Square, 8 in
An 8 inch try square with a stainless steel blade and a carbonized bamboo handle with a routed grip. Graduations in 1/8 and 1/16 inch are etched into the blade. The listing gives the size as 11.3 by 1.1 inches and the weight as 6.08 ounces, and the maker adds a limited lifetime warranty. The material line says stainless steel while the handle is bamboo.
Suits: a light everyday square. Strengths: a bamboo handle and a lifetime warranty. Weaknesses: the listed material field mentions only the blade. Skip it if you want a longer blade.

Best for layout with a pencil or scribe
2. Arrow 10-Inch Try Square with Stainless Steel Blade
A 10 inch square with a stainless steel blade marked in metric and SAE at 1/16 inch, an aluminum alloy handle, a built-in bubble level, a screw-in brass scribe and a 45 degree face. The blade has notches spaced at 1 inch or 1 centimeter for drawing parallel lines with a pencil. The listing gives no blade thickness.
Suits: layout with a pencil or scribe. Strengths: the longest blade and the most extras. Weaknesses: more parts than a plain square. Skip it if you want a fixed, one piece style.

View Arrow 10-Inch Try Square, Woodworking Square with Stainless Steel Blade on Amazon
Best for bench work and joinery
3. Swanson TS152 8-Inch Try Square with Hardwood Handle
A classic 8 inch try square with a solid hardwood handle bound in brass and a stainless blade etched in 1/16 and 1/8 inch. The maker says the inside face of the handle sets the blade at 90 degrees with no moving parts. The listing weight is 7.36 ounces.
Suits: bench work and joinery. Strengths: no moving parts and an etched scale. Weaknesses: no level or scribe. Skip it if you want a square with extra features.
View Swanson Tool TS152 8-Inch Try Square with Hardwood Handle on Amazon

Best for layout on site or in the shop
4. Swanson SVR149 9-Inch Savage Try Square
A 9 inch square with an anodized aluminum frame, a rubber coated handle insert, a retractable kickstand and a scribe bar cut into the stainless blade. The maker says the kickstand holds the blade at 90 degrees on the stock without a hand. The listing size is 9.53 by 1.57 inches and the scale is 1/16 inch.
Suits: layout on site or in the shop. Strengths: a hands-free stand and a scribe bar. Weaknesses: the kickstand is an extra moving part. Skip it if you like a plain wood handle.

Best for a traditional bench square
5. Spear and Jackson CTS9 9 Inch Carpenters Try Square
A traditional carpenter’s try square with a rosewood stained hardwood stock, brass top and bottom faces and a spring steel blade. The title says 9 inch, but the details table lists 6.5 by 0.71 inches, and the bullets give the base as 165 millimeters long and 48 by 18 millimeters. The listing shows no scale, so check the size before you buy.
Suits: a traditional bench square. Strengths: a hardwood and brass build. Weaknesses: conflicting sizes and no scale detail. Skip it if you need a confirmed blade length.

View Spear and Jackson CTS9 9 Inch Carpenters Try Square on Amazon

Best for small parts, setups and metalwork
6. Faithfull Engineers Steel Try Square, 150mm (6in)
A 6 inch engineer’s square with a precision ground, hardened and tempered steel blade. The bullets give an overall size of 173 by 100 by 11 millimeters, a blade thickness of 1.7 millimeters and an inner size of 150 by 75 millimeters, while the details table lists 7.24 by 4.33 inches. The maker names metalwork and woodwork.
Suits: small parts, setups and metalwork. Strengths: a compact steel build. Weaknesses: short, with no scale described. Skip it if you work across wide boards.
Care and Setup
- Check a new square by drawing a line, flipping the square and drawing it again.
- Wipe steel blades after use.
- Keep the stock against a true, straight edge.
- Store squares flat or hung so the blade is not bent.
Mistakes to Avoid
- Assuming a square is exact without checking it.
- Dropping a square on a hard floor.
- Trusting a title length when the details table says otherwise.
- Using a square as a pry bar or a scraper.
Try Squares Compared With Other Squares
A try square is one of several tools that check right angles, and it helps to know where it fits before you buy. The try square has a short blade fixed to a stock, and the stock rides along an edge. It is aimed at checking and marking small to medium pieces, especially at the bench.
A combination square has a blade that slides along a head, so it can also measure depth and mark 45 degree angles. It is more flexible, but the sliding head introduces another joint that must stay tight. A framing or speed square is a triangle designed for rough carpentry and quick angle marking. A engineer’s square is a solid steel square used in metalwork, where a thin blade and a precise inner angle matter. A large framing square handles big layouts such as stair stringers.
The try square is simple. Because the blade is fixed, there is no slide to loosen and fewer sources of error. That makes it a good fit for woodworkers who want a trustworthy reference at the bench and who mostly work on boards of modest width.
- Choose a try square for joinery, checking cut ends and marking across a board.
- Choose a combination square if you also need depth and 45 degree marking.
- Choose a speed square for fast rough carpentry.
- Choose an engineer’s square for small, precise metal setups.
Many people end up owning more than one, since each handles a slightly different job.
Blade and Stock Materials Compared
The blade and the stock are made from different materials, and each combination has strengths. Stainless steel blades resist rust and are common on layout squares. Hardened or spring steel blades hold an edge and can be very straight, but they may need wiping to keep rust away. Blade thickness affects how well the blade registers against a board and how easily you can scribe along it.
Stock materials include hardwood, bamboo, aluminum and steel:
- Hardwood stocks are traditional, comfortable and often bound in brass for wear. They can move slightly with humidity, so store them in a stable spot.
- Bamboo stocks are light and tough and are often treated to resist moisture.
- Aluminum stocks are stable and durable and often carry extras such as levels or scribe bars, though they can dent if dropped.
- Steel squares are all one material, which keeps them stable but heavier and prone to rust without care.
Check how the blade joins the stock. A blade that is riveted or pinned and set flush against the stock is the foundation of accuracy. Any play or gap is a warning. The listing may describe the fastening, and feedback may mention loose joints.
If the listing gives conflicting information about the material or size, as some do, confirm the details before you rely on the square. Material affects weight, feel and long-term stability, so pick the one that suits where and how you work.
Testing Accuracy at Home
No listing in this guide gives a measured accuracy figure, so a simple check at home is the best way to learn whether a square is true. You can do this with only a board and a pencil, and it is worth doing as soon as the square arrives.
Start with a board that has a straight, flat edge. If you are unsure that the edge is straight, plane or sand it until it is. Hold the stock firmly against the edge and draw a fine line along the blade. Flip the square over so the stock sits against the same edge from the other side, align the blade with the start of your line and draw a second line. If the lines match perfectly, the square is true. If they diverge, the angle is off, and the size of the gap shows how far.
A few cautions help:
- Use a sharp pencil or a marking knife so the line is thin.
- Keep firm pressure on the stock against the edge.
- Repeat the test in a couple of spots to be sure.
- Check again after any fall or knock.
If a square fails the test, consider returning it. Some fixed squares cannot be adjusted, and a square that is slightly off will cause errors in every joint. Some woodworkers keep one square as a reference and never use it for rough work.
Using a Try Square Well
Good technique matters as much as a good tool. A try square gives its best results when the stock is held tight against a straight, clean edge, and when the pressure is applied toward that edge, not away from it. Keep your fingers away from the blade if you are scribing with a knife.
For marking a line across a board, press the stock against the edge, slide the square to the mark and draw along the blade. For checking a corner, set the stock against one face and see whether the blade touches the adjoining face along its full length. Look for light gaps, which show that the corner is out of square. Holding the work up to a light source makes small gaps easier to see.
When you check a joint, test both inside and outside corners if the shape allows. For a cut end, hold the square against the long edge and look at the end of the board for a gap. A small difference is a signal to trim or plane again.
- Keep the blade and edge free of dust, which can add error.
- Use a knife line for precise work, since it gives a thinner mark than a pencil.
- Do not lean on the blade or use it as a straightedge for cutting.
- Avoid prying with the blade, which can bend it.
With practice, you will find that a reliable try square speeds up work and reduces errors.
Budget Tiers and Questions to Ask Before Buying
Try squares span a range of cost. Lower-cost squares suit casual work, general home projects and people building a basic kit. Mid-range squares often offer better materials, clearer markings and steadier construction. Premium squares usually aim at craftspeople who need dependable accuracy and are willing to pay for better machining and finish. A higher price does not guarantee accuracy, so test any square you buy.
Questions to ask before buying:
- How long should the blade be for the boards I work with?
- Do I want a plain square or one with a level, scribe or stand?
- Is the scale etched or printed, and which units does it use?
- Do the title, bullets and details table agree on size and material?
- Is there a warranty, and what does it cover?
- What do buyers say about accuracy and loose parts, and how many people rated it?
Signs that a square needs replacing include a loose blade, a stock that is chipped or warped, a blade that is bent or kinked, deep rust pitting along the working edge or a failed flip test. A square that has been dropped on a hard floor should be checked right away. Using a square that is no longer true leads to joints that do not close, so replacing it is cheaper than the wasted wood.
Which try square should you buy?
The best try square is the one whose blade length and build match your work, so start with the boards you cut most often. Here is how the six squares map to common needs.
- A light, everyday bench square: the Johnson 1940-0800 with its bamboo handle and etched scale.
- Longest blade and extra functions: the Arrow 10-inch, which adds a bubble level, a brass scribe and a 45 degree face.
- Classic joinery with no moving parts: the Swanson TS152, a hardwood and brass square with a fixed seat.
- Hands-free layout with a scribe bar: the Swanson SVR149, which has a retractable kickstand.
- A traditional hardwood and brass look: the Spear and Jackson CTS9, but confirm the real size first because the listing conflicts with itself.
- Small parts and metalwork: the Faithfull 150mm engineer’s square, a compact steel tool.
If you are buying your first try square for woodworking, a plain fixed square with a clear etched scale is easy to trust and easy to check. Add a level or kickstand only if you will use them.
What to check before you buy a try square, and who should skip it
Before you buy a try square, check the blade length, the scale and how the blade is joined to the stock. These details tell you more than the headline name.
- Compare the title, bullets and details table for size and material.
- Check whether the scale is etched, printed or missing.
- Look at the units, since some are inch only and others add metric.
- Read the warranty field and return terms.
- Plan to run the flip test the day it arrives.
Weigh the trade-offs honestly. Wood and bamboo feel pleasant but can shift with humidity. Aluminum is stable but can dent if dropped. Steel is precise but needs wiping against rust. Extras such as levels and kickstands add uses, yet each is another part that can loosen. No listing here gives a measured accuracy figure, so a square is only as good as your own test.
Think about how the square will be handled. A square that lives in an apron pocket or a toolbox will get knocked, so a sturdier build and a quick recheck habit matter. A square that stays on a bench rack can be a delicate reference tool. Many woodworkers keep one square for rough work and another for fine layout, which keeps the careful one true for longer.
Also think about the work itself. Cabinet parts and small boxes suit a shorter blade that is easy to control. Wider panels need a longer blade, or you may end up stepping the square along the board, which adds error. Choose the length for the widest piece you check regularly.
You might skip a try square if you mostly need to mark angles on large framing lumber, where a speed square or a framing square is quicker, or if you need depth and 45 degree marking on one sliding tool. Otherwise, compare the picks above, check the current listing for size and what is included, then choose the one that fits how you will use it.
Try Square FAQ
How do I check a try square?
Hold the stock against a straight edge and draw a line along the blade. Flip the square over and draw again. If the two lines are not the same, the square is off.
Which square has the longest blade?
The Arrow lists 10 inches. The Swanson SVR149 lists 9 inches, and the Faithfull is the shortest at 150 millimeters.
What size try square should I buy first?
A blade of moderate length suits most bench work and fits in a typical toolbox. Choose a longer blade only if you regularly mark across wide boards.
Can I adjust a try square that is out of true?
Most fixed try squares are not designed to be adjusted. If a square fails the flip test, returning or replacing it is usually the sensible option.
Is a square with a bubble level useful?
A level can help for quick checks on a job site, but it adds parts and is not a substitute for a good bench reference. It suits layout and rough work more than fine joinery.
How do I protect a steel blade from rust?
Wipe it after use and keep it in a dry place. A light coat of oil or wax on carbon steel helps, and stainless blades need less attention but still benefit from drying.
What is the difference between a try square and an engineer's square?
A try square usually has a thin blade attached to a thicker stock, and it is aimed at woodworking. An engineer's square is a solid steel tool used mainly for metalwork and setup checks.
Should I use a pencil or a knife with a try square?
A knife gives a thinner, more precise line and is common for joinery. A pencil is faster and fine for rough layout.
How should I store a try square?
Keep it flat or hung up so the blade does not bend. Store it away from moisture and heavy tools that could press on it.
What is a try square used for?
A try square checks that an edge or corner is at a right angle and marks lines across a board. You hold the stock against an edge and run a pencil or knife along the blade. It is a common tool for joinery and bench work.
What blade length is best for a try square?
A moderate length suits most bench work and small to medium boards. Choose a longer blade if you regularly mark across wide stock. A short blade is easier to carry and better for small parts.
Is a wooden or metal handle better on a try square?
Neither is better in every case. Wood and bamboo feel comfortable and light, while aluminum is stable and often carries extras. Pick based on weight, feel and whether you want a level or scribe.
Why does the flip test show a gap on my square?
A gap means the blade is not at a true right angle to the stock, or the edge you tested against is not straight. Recheck on a clean straight edge first. If the gap remains, the square is off and should be returned or replaced.
Can I use a try square as a straightedge?
It can guide a pencil line along the blade, but it is not designed as a full straightedge. Do not use it to guide a knife for heavy cuts, and do not lean on it. Keep it for marking and checking.
How do I clean a try square?
Wipe the blade with a dry cloth after use and remove dust from the edge where the stock meets the work. A light wipe of oil or wax helps carbon steel, and wood parts should be kept away from moisture. Store it flat or hung.
Building Square-Checking Into Your Workflow
A try square pays for itself in the checks you make before cutting, not in the lines you draw after. Build three checks into your routine. First, check the stock itself: hold the square against the reference edge and sight along the blade for gaps of light, because marking a line from an edge that is not straight produces a line that is square to nothing. Second, check the setup: after setting a fence, a mitre gauge, or a machine table, verify with the square before the first cut and again after any adjustment, since a setup that drifts slightly will drift on every part in the batch. Third, check the result early: test the first cut piece, not the tenth, so a small error costs one offcut instead of a morning of matching mistakes.
The flip test described elsewhere in this guide deserves emphasis because it is the only accuracy check that needs no reference tool. Scribe a line, flip the square, scribe again from the same edge, and compare. Any divergence between the two lines is twice the error of the square itself, which makes even small errors visible. Run it when a square is new, after any drop, and at the start of a project that matters. A square that fails gets retired to rough duties such as checking packaging, garden timber, and other work where its error cannot propagate into joinery.
Matching the six squares to hands and trades
The Johnson bamboo-blade model is the light option: easy to carry, kind to finished surfaces, and well suited to site work, picture framing, and any job where the square lives in a tool belt rather than on a bench hook. Bamboo also shrugs off the damp that swells a wooden stock. The Arrow 10-Inch, the longest blade in this group, suits sheet goods, carcasses, and layout on wider boards where a short blade forces you to slide and re-register, introducing error at every move. The Swanson 8-Inch hardwood-handled square is the traditional bench tool: the stock sits comfortably for marking shoulders and checking small joinery, and its proportions suit furniture-scale work.
The Swanson Savage 9-Inch takes a more engineered approach, aimed at users who want a robust, modern stock that tolerates site handling. The Spear and Jackson 9 Inch carpenters square represents the classic British pattern, a familiar balance for general carpentry and bench work alike. The Faithfull engineers steel square, at the smallest size here, is the precision outlier: an all-steel tool for metalwork, machine setup, and checking other tools, where its rigidity and fine manufacture matter more than blade length. Owning one bench square and the small engineers square covers nearly every checking task in a mixed workshop, which is a more useful pairing than two mid-size squares that duplicate each other.
Head-to-Head: Stock Materials and Blade Behaviour
The stock, the part you hold against the edge, decides how a square feels and how long it stays true. Wooden and bamboo stocks are warm, light, and forgiving if dropped, but they can wear on the reference face over years of sliding along abrasive edges, and that wear quietly becomes error. Metal stocks resist wear and survive site abuse, at the cost of weight and a colder, harder contact that can mark soft finished timber if you are careless. Engineered stocks aim between the two, trading some traditional feel for stability. None of these is a wrong answer; the right one follows your environment, with damp and site work favouring stable, moisture-resistant materials and fine bench work favouring whichever stock you handle most carefully.
Blade behaviour matters in two ways. A blade with clear, etched graduations supports measuring and marking in one motion, though a try square should never be your primary ruler; treat the markings as convenience, not gospel. Blade stiffness matters when the square is used to guide a knife: a thin, flexible blade can deflect under knife pressure and curve the very line it was meant to keep straight, so press the knife lightly and let the stock face, not force, do the guiding. Finally, consider how the blade meets the stock: any looseness at that joint is fatal to accuracy, and it is the first thing to check on an older square and the main thing you are paying for on a better one.
Marking with knife versus pencil, and squaring larger work
A knife line severs fibres and gives a chisel or saw a physical register; a pencil line is faster, visible, and removable. Use the knife where the line is a final shoulder or a show surface, and the pencil for rough layout, waste-side marks, and anything you may need to move. Keep the knife flat against the blade and draw it toward you in one or two light passes; sawing at the line widens it. For work larger than the blade, do not slide the square along in hops and hope the errors cancel. Instead, strike the line in sections from a verified straightedge, or step up to diagonal checks: on a frame or carcass, equal diagonals are a more reliable proof of square than any single corner check, and the try square then serves to verify individual corners within an assembly already proven by measurement.
Troubleshooting Out-of-Square Results in Order
When parts come out not square, diagnose before adjusting anything expensive. First, test the square itself with the flip test; tools get dropped, and blaming a machine for a bent square wastes an afternoon. Second, check the reference edge of the stock with a straightedge, since a square used from a wavy edge produces faithfully wrong lines. Third, check your technique: the stock must sit flush along its whole face, not rocked onto one corner, and the blade must lie flat on the work, not propped on a shaving or a burr. Fourth, check the marking tool: a thick pencil line invites cutting to the wrong side of it, so confirm everyone in the shop knows which side of the line is waste. Fifth, only then suspect the saw or machine setup, and verify it by cutting a test piece and checking that piece with the now-proven square. Care between jobs is simple: hang the square or lay it flat, keep steel blades lightly oiled in damp shops, never use the blade as a scraper or pry, and store it where heavier tools cannot fall across it. A square is a reference, and references only stay useful if they are treated more gently than the tools they check.
Choosing by Scenario: Bench, Site, Classroom and Metalwork
The bench woodworker’s square lives within arm’s reach and is used dozens of times a day for small, precise checks: tenon shoulders, drawer parts, the squareness of a planed edge. For this user, an eight or nine inch blade covers nearly everything, the stock should sit comfortably for one-handed use, and the traditional patterns from Swanson and Spear and Jackson fit the rhythm exactly. The site carpenter’s square leads a harder life in a belt or a van, gets dropped, and checks studs, plates, and trim in variable weather; stability against moisture and knocks pushes this user toward bamboo or engineered stocks, and toward treating the square as a consumable to be flip-tested often and replaced without sentiment when it drifts.
The teacher or shared workshop needs squares that survive learners and stay verifiable: several identical mid-size squares, each flip-tested at the start of term and marked with the date it last passed, teach students the right lesson, that references are checked, not assumed. The metalworker and machine setter need the engineers pattern: the Faithfull steel square’s rigidity and fine faces suit checking machine setups, scribing on steel, and verifying other tools, tasks where a wooden stock would be out of its element. The picture framer and box maker, working small and exact, often do best with the smaller end of the range used alongside a shooting board, where the square’s job is as much guiding as checking.
A worked routine: squaring a board from rough to ready
Begin with one face flattened and marked as the reference. Plane or select one long edge straight against that face, and prove it with the square at several points along its length, sighting for light gaps; a single check at one end proves nothing about the middle. Mark the second edge from the first using the square to carry lines across at both ends, then work to those lines and check again. For the ends, hook the stock over the proven edge and scribe the end line with a knife, then cut just outside it and finish to the line, checking the result against both the face and the edge. The board is now square in the only sense that matters for joinery: each new surface was derived from a proven one, in sequence, with the square as the transfer instrument at every step. Skipping the sequence and checking only at the end is how small errors hide until assembly exposes them all at once.
Comparing Try Squares With Combination and Speed Squares in Practice
Each square type earns its place, and confusion between them causes most buying mistakes. The try square is a fixed reference: no moving parts, nothing to set, nothing to slip, which is why it remains the bench standard for checking and for knife lines. A combination square adds a sliding rule and adjustable heads, gaining versatility for depth, marking, and machine setup while introducing a joint that must be kept clean and locked to stay true. A speed square is a site tool for rafter geometry and quick saw guides, robust and fast, but its thick body and markings are not designed for fine bench checking. Owning a try square plus one of the others covers more ground than owning two try squares of similar size, unless your work is so bench-bound that the second try square is a deliberate spare kept proven for critical work.
Within the try square family, the honest comparison is condition and fit rather than brand mythology. A modest square that passes the flip test today is a better reference than a famous name that fails it. Check the stock face for flatness by sighting along it, check the blade for bends the same way, and check the joint between them for any play by holding the stock firmly and pressing the blade tip sideways. Graduations, finish, and handle comfort decide between squares that all pass those tests, and at that point personal preference is a legitimate deciding factor, because a tool you enjoy handling is a tool you reach for, and the check you actually make is the only one that protects the work.
Teaching the flip test and building a checking habit
If you teach one thing to a new woodworker, teach the flip test, because it converts trust into verification in ten seconds. Write the date a square last passed on a small label on its stock; the label creates the habit of re-testing after drops and at project starts. Extend the same habit to assemblies: before glue, dry-fit and check diagonals; after glue, check again while adjustment is still possible. Keep the proven square in a defined place, hung or in a drawer slot, separate from the rough square used for garden and packaging work, and never let the two swap roles silently. Accuracy in a workshop is rarely about owning a perfect tool; it is about knowing, today, whether the tool in your hand is true, and that knowledge is a habit, not a purchase.
Squares in Assembly: Glue-Up Checks That Save Projects
The most valuable square checks happen during assembly, when correction is still possible. Before glue, dry-assemble the piece and check it three ways: corners with the try square, overall truth with diagonal measurements, and flatness by sighting across the faces. If the dry assembly is wrong, the glued one will be wrong with stress added, so fix parts now. During glue-up, check the diagonals again immediately after clamping, because clamping pressure routinely pulls an assembly out of square even when every part was perfect; adjust clamp position or add a diagonal brace while the glue is fresh. After the glue cures, a final check tells you whether the piece can proceed to fitting doors and drawers, which will advertise any remaining error mercilessly.
Drawers and doors deserve their own check: a drawer box that is slightly out of square binds in a square opening, and the instinct to plane the drawer is often wrong; measure both, and correct the one that is actually at fault. The try square settles the question part by part. Similarly, when a frame-and-panel door rocks on a flat surface, the square distinguishes twist from a simple high corner, and the remedies differ. Assembly is where all the small accuracies of the earlier stages are summed, and the square is the auditor that reads the total honestly.
Building a reference corner in the workshop
Serious workshops keep a reference corner: a surface and an edge that have been proven flat, straight, and square, against which tools and work can be checked quickly. A section of a well-made bench, a machined table, or a dedicated reference board can serve. The reference corner turns verification from an event into a habit, because the check takes seconds when the reference is always at hand. Prove the reference itself periodically against the flip test and diagonal methods, since a reference that drifts corrupts everything checked against it. With a reference corner, the flip test, and one proven square, a small workshop possesses a complete local system of truth, and every project built inside that system starts with an advantage that no purchase can substitute for: the knowledge that its measurements mean what they say.
Squares and Machine Setup: A Quieter Role
Beyond hand work, the try square quietly audits machines. A rip fence that is not parallel, a mitre gauge that has drifted, a drill-press table that is not square to the spindle: each announces itself first as work that mysteriously will not assemble, and the square, applied at the machine before the next batch, finds in a minute what test cuts find in an hour. Use the engineers pattern for spindle work, where its all-steel faces register cleanly, and the bench squares for fences and tables. Check after any machine is moved, knocked, or adjusted, and after any blade or bit change that involved tilting an arbor or a table, because those operations disturb exactly the relationships the square verifies.
Keep the habit documented in the simplest way: a note on the machine, dated, recording when it was last proven square and by whom. In a shared shop the note prevents both duplicate effort and the worse failure of everyone assuming someone else checked. Accuracy, once again, turns out to be a system of small verifications rather than a property of any single tool, and the try square is the verification instrument that costs the least and is asked the most.
Passing a square on: what to tell the next owner
Good squares outlive their buyers, and a square passed on with its history is worth more than the same square anonymous. If you hand one down, say when it last passed the flip test, what work it was reserved for, and how it was stored. The story teaches the new owner the habits that kept it true, and habits, transferred with the tool, are the real inheritance in any workshop.
A final word on value
The try square is among the cheapest references in the workshop relative to the cost of the errors it prevents. A single mis-cut in good hardwood, a single frame glued out of square, or a single machine setup left unproven costs more than the difference between the modest and the premium options here. Buy the square whose stock suits your hand and your environment, prove it on arrival, and then spend your remaining attention on the checking habits that make any square valuable: test before cutting, test the first piece, and test again at assembly, every time, without exception for small jobs.
There is also a quiet satisfaction in a proven square that has nothing to do with specifications. It is the tool you reach for without thinking, the reference whose verdict ends arguments with machines and materials alike, and its presence on the bench sets the standard for every other measurement in the room. Keep it proven, keep it protected, and it will keep your work honest for longer than most of the projects it checks.
The Short Version
For a light bamboo handle, the Johnson. For a long blade with a level, the Arrow. For a classic wood handle, the Swanson TS152. For a hands-free stand, the Swanson SVR149. For a traditional hardwood and brass look, the Spear and Jackson. For a small steel square, the Faithfull.





