Choosing a drill bit comes down to two questions: what material you are drilling and what the hole is for. This cheat sheet gives general rules that hold true across makers. For exact sizes, always check the screw or anchor packaging and the maker’s chart. Beyond the table, you will find a conversion guide, a worked example, common scenarios and a troubleshooting table.
Hole Purpose Reference
| Hole type | Rule of thumb | Why |
|---|---|---|
| Pilot hole | About the width of the screw’s inner shaft, not the threads | Lets threads bite while limiting splitting |
| Clearance hole | Slightly wider than the screw’s outer thread | Lets the top board slide down and pull tight |
| Countersink | Cone shaped to match the head | Sets the head flush or below |
| Anchor hole | Size printed on the anchor packaging | Wrong width weakens the hold |
| Dowel hole | Same width as the dowel | Gives a snug fit for glue |
In this guide
Bit Types by Material
- Wood: twist bits for general work, brad-point bits for clean entry, spade or auger bits for larger holes.
- Metal: twist bits made for metal, used at lower speed with a cutting lubricant if the maker advises.
- Masonry: bits with a hard tip, used with a hammer setting only if the tool and bit allow.
- Tile and glass: special tipped bits, drilled slowly with care.
Reading Sizes
Bits are labeled in fractions of an inch, millimeters, or numbered and lettered sets. Metric and inch sizes are close but not identical, so a mix can leave a loose fit. Use a bit gauge or a chart to confirm a size if the marking has worn off.
Handy Inch-to-Millimeter Conversions
These are plain arithmetic conversions, rounded, and handy when a plan uses one system and your bits use the other. Remember that one inch is 25.4 millimeters.
- 1/8 inch is about 3.2 mm.
- 3/16 inch is about 4.8 mm.
- 1/4 inch is about 6.4 mm.
- 5/16 inch is about 7.9 mm.
- 3/8 inch is about 9.5 mm.
- 1/2 inch is about 12.7 mm.
The nearest metric bit is usually a little different, which can matter for tight fits such as dowels. For tapped threads, where you cut a thread in the hole, use the drill size given on the tap maker’s chart and not a guess from this list.
Good Drilling Habits
- Mark the spot and make a small dimple to guide the tip.
- Clamp or hold the work firmly.
- Drill at a steady pace, easing off as you break through.
- Back the bit out to clear debris from deep holes.
- Check for hidden pipes or wires before drilling into walls, and ask a qualified professional if unsure.
Wear eye protection and follow the tool’s manual.
Bits do their best work when they are clean and sharp. Wipe them after use, keep them in an index case where each size has a slot, and check the tip for rounding or chips. A dull bit pushes harder, heats up, and wanders. Some people sharpen bits with a guide made for the job, and others simply replace them. Avoid dropping bits into a loose pile, since they knock against each other and dull the edges.
Worked Walkthrough: Joining Two Boards with a Screw
This example uses an invented screw only to show the method. Always use the sizes your screw packaging recommends.
- Look at the screw. Identify the thread, which is the ridge, and the core, which is the solid shaft between the ridges.
- Choose the pilot bit. Hold bit candidates against the screw from the side. The right bit covers the core but leaves the thread ridges visible on both sides.
- Choose the clearance bit. For the top board only, hold bits against the screw. The right one is about as wide as the outer thread, so the screw slides through without biting.
- Clamp the boards in their final position, then mark the hole.
- Drill the clearance hole through the top board, then the pilot hole into the lower board using the same mark.
- Countersink if you want the head flush. Test on scrap first, because a cone cut too deep weakens the top board.
- Drive the screw until it is snug. If the wood is dense and the screw binds, back out and widen the pilot slightly.
Common Scenarios
Hardwood that splits
Dense wood needs a careful pilot hole and a clearance hole in the top piece. Keep holes away from edges and ends.
Softwood and a loose screw
If the screw spins without gripping, the pilot may be too wide. Try a smaller bit on scrap and compare.
Wall anchors
The anchor packaging states the bit size. Use that size and follow its instructions for the wall material and load. For load-bearing needs, ask a qualified professional.

Thin sheet metal
Clamp it to a backing board, use a sharp metal bit at low speed, and deburr the edges so they are not sharp.
Quick Troubleshooting
| Symptom | Likely cause | What to try |
|---|---|---|
| Hole too big for the screw | Bit wider than the core | Use a narrower bit on a new spot, or fill and redrill |
| Screw breaks or binds | Pilot too narrow for the material | Back out, widen slightly, drive again |
| Wood splits near the end | No pilot or hole too close to the edge | Drill a pilot and move the hole inward |
| Bit slides off the mark | No dimple or dull tip | Mark with a punch or awl and begin slowly |
| Ragged exit hole | No backing board | Clamp scrap behind the work |
Mistakes to Avoid
- Using the same bit for every screw. Different screws have different cores, so check each against the bit.
- Skipping the test on scrap. A quick trial prevents ruined parts.
- Drilling into walls blind. Pipes and cables can lie behind a surface.
- Running a bit too fast in metal. Heat dulls the edge quickly.
- Forcing a dull bit. It wanders and burns, so replace or sharpen it.
Care and Upkeep Over Time
Keep bits in an index case with each size marked. Wipe off resin and metal swarf after use, and apply a light coat of oil to bare steel bits if the maker advises. Check tips for chips or rounding before each job, and set aside any bit that no longer cuts cleanly. Keep replacements of the sizes you use most.
Controlling Hole Depth
Many jobs need a hole that stops short of the far side of the work. Screws that are too long can poke through a thin panel, and a pilot that runs deeper than the screw wastes holding power. The simplest depth guide is a strip of masking tape wrapped around the bit at the mark you want. When the tape touches the surface, stop. It is cheap, quick and easy to move for the next hole.
Other options are a depth stop collar that clamps onto the bit shank, or a stop built into some drill guides. Collars grip by a small screw, so check that the screw is tight before each use, because a collar that slips can leave you with a hole that is too deep. Measure from the tip of the bit, not from the chuck, and remember that the cone-shaped point adds a little extra beyond the full-width part of the hole.
For blind holes that hold a screw, aim for a pilot that is a little deeper than the threaded length, so the tip of the screw has room and wood dust has somewhere to go. Test the depth on scrap, then compare the scrap hole with the screw before you commit to the real piece.
Matching the Bit to the Screw Head Type
The head of a screw changes what holes you need. A flat countersunk head sits in a cone-shaped recess, so you need a countersink cutter or a combination bit that drills the pilot and shapes the cone in one pass. A pan or round head sits on top of the surface, so a clearance hole is enough and no cone is needed. A washer head spreads load over a wider area and needs no special cutting at all in most wood.
Before you start, hold the screw next to the board and picture where the head will end up. If you want it flush, the cone must be as wide as the head and only as deep as the head is tall. Cutting too deep thins the wood and weakens the joint, so work in small steps and test the fit with the actual screw.
Combination bits are sold for common screw sizes, and the packaging usually says which screw each bit suits. Treat that information as a initial point, since wood hardness and screw design differ between makers. If a screw feels tight or loose in your test hole, adjust by trying the next size up or down on scrap.
Drilling Plastic and Laminated Boards
Plastics and coated boards behave differently from solid wood. Plastics can melt if the bit runs fast, and they may crack when a bit grabs on break-through. Use a sharp bit, a low speed and light pressure, and back out often to clear shavings. Some plastics are brittle, so clamp them between two scrap boards to support both faces and reduce stress around the hole.
Laminate, melamine and veneered boards have a thin, hard surface layer over a softer core. The surface chips easily on the exit side, so place a backing board behind the work. A strip of tape on the mark can also help hold the surface layer together while the bit enters. Let the tip start slowly so it does not skate across the glossy face.
For particleboard and similar panels, screws hold best when the pilot is on the snug side and the screw is not driven too hard, since the core can crush or strip. Check the screw maker’s advice for fastening into panel products, and consider fittings made for the purpose where a joint will be moved or loaded repeatedly.
Setting Up the Drill Before You Begin
A well-chosen bit still gives poor results if the drill is set up badly. Start by seating the bit fully in the chuck and tightening it as the manual describes. A bit that sits crooked wobbles, which makes the hole larger than the bit and rough on the sides. Check that the bit runs true by spinning the chuck by hand and watching the tip.
Next, look at the speed and clutch controls. Lower speeds suit large bits, metal and plastics, while higher speeds suit small bits in wood. If your drill has a hammer or torque setting, make sure it is on the correct mode for the material, because the wrong mode can damage the bit or the work. Many drills also have a forward and reverse switch, so confirm the direction before you pull the trigger.
Finally, think about your stance and grip. Keep the bit square to the surface from two directions, using a small square or just your eye against a nearby edge. A drill guide or drill stand can help for repeatable holes. Hold the tool firmly and keep your free hand clear of the bit path.
Choosing and Buying a Bit Set
When you buy bits, start with the sizes you actually use. A basic set of twist bits covers most household work, and you can add specialist bits one at a time as jobs arise. Check what the set says about the intended materials, since some are meant for wood and plastic only, while others are made for metal as well. The listing or packaging should say.
Look at the case. An index case with a labeled slot for each size makes it easy to see which bit is missing and to pick the right one quickly. Cases that are flimsy or have loose lids tend to spill their contents, so check how the lid latches. Think about whether the set includes sizes that match the screws and anchors you use, and whether you can buy single replacements for the sizes that wear out first.
Budget tiers differ mainly in material, finish and the care taken in grinding the tip. Lower-cost sets suit occasional light jobs. Better sets suit frequent use or harder materials. Read the product description closely, and check how people describe wear and sizing accuracy in general terms before deciding.
A Short Glossary of Drill Bit Terms
Bit packaging uses a handful of words that are easy to mix up. This glossary covers the ones you will see most often.
- Shank. The smooth or shaped end that sits in the chuck. Round, hex and quick-change shanks each fit different drills.
- Flute. The spiral groove that carries chips out of the hole.
- Point angle. The shape of the tip, which affects how the bit bites into different materials.
- Pilot hole. A small hole drilled first to guide a screw or a larger bit.
- Clearance hole. A hole slightly larger than a screw shank so the screw passes through freely.
- Countersink. A cone-shaped recess that lets a screw head sit flush.
- Fractional and metric sizes. Bits are sold in fractions of an inch or in millimeters, and the two systems do not line up exactly.
Matching Bit Type to Material
Choosing the right type of bit matters as much as choosing the size. The table below sums up the usual pairings, and your drill and bit packaging should be checked for the maker’s own guidance.
| Material | Bit type that is commonly used |
|---|---|
| Softwood and plywood | Twist bits or brad point bits |
| Hardwood | Brad point or sharp twist bits, with slower speeds |
| Metal | High-speed steel or coated twist bits with cutting lubricant |
| Brick, block and concrete | Masonry bits, often with a hammer drill |
| Tile and glass | Special tile or glass bits, used gently |
| Plastic | Sharp twist bits at moderate speed |
Picking a Size for Common Jobs
Hole size depends on what goes into it. For a wood screw, the pilot hole is generally smaller than the screw thread, while the clearance hole in the top piece is a little larger than the screw shank. For wall anchors, the packaging states the exact bit size required, so match it closely. For bolts, the hole is usually a touch larger than the bolt diameter. When the pack lists a bit size, follow it instead of guessing from a chart.
If you are unsure, drill a test hole in a scrap piece of the same material and see how the screw or anchor fits.
More on Mistakes to Avoid
- Using a wood bit on metal, which dulls the tip fast.
- Drilling at high speed in hard material, which makes heat and can ruin the bit.
- Pushing too hard instead of letting the bit cut.
- Skipping a pilot hole near the edge of a board, which can split the wood.
- Drilling into walls without checking for hidden pipes or wires. When in doubt, use a detector or consult a professional.
Care and Storage
Wipe bits clean, keep them in an indexed case so the sizes stay visible and replace any that are bent or dull. Wear eye protection and follow the drill maker’s instructions.
A Quick Checklist Before You Drill
- Check the material and choose the matching bit type.
- Read the screw, anchor or bolt packaging for the recommended hole size.
- Mark the spot with a pencil or a small center punch so the tip does not wander.
- Set a depth guide with tape on the bit if you need a blind hole.
- Clamp small workpieces so they cannot spin.
Products Worth a Look
As an Amazon Associate, UMT Smart Tool earns from qualifying purchases. These picks come from our guide: How to Choose the Best Drill Bit Sets: Buyer's Guide (2026).
-
DEWALT Titanium Pilot Point Drill Bit Set, 21-Piece (DW1361)
-
IRWIN Cobalt Drill Bit Set, 29-Piece (3018002)
-
Bosch Cobalt M42 Drill Bit Set, 14-Piece (CO14B)
Reading the Cheat Sheet Step by Step, With the Arithmetic Checked
A drill bit cheat sheet compresses three measurement systems into one grid, and it rewards a slow, methodical reading. Begin by identifying which column family your information arrives in. A screw packet may state a size in millimetres, an older plan may give a fraction of an inch, and a bit case may be stamped in decimals. Your first task is translation, not selection: find the row for the size you were given, then read across to the system your bit set uses. Only after the translation is fixed should you ask the second question, which is whether that size serves as a pilot hole, a clearance hole or a direct hole for an anchor, because the same diameter plays different roles in different jobs.
The conversions themselves are simple enough to check by hand, and checking them builds the confidence to catch a misread row. One inch equals exactly twenty-five point four millimetres by definition, so any inch size multiplied by that figure gives its millimetre equivalent. A quarter inch, for example, is nought point two five inches; multiply by twenty-five point four and you get six point three five millimetres, which is why the chart shows that pairing. An eighth of an inch is nought point one two five, giving roughly three point two millimetres. A three-eighths bit is nought point three seven five inches, which converts to about nine point five millimetres. If a row on any chart disagrees with that multiplication, the row is wrong or you are reading the wrong row, and either discovery is valuable.
Fractions convert to decimals by plain division, and doing the division once or twice fixes the pattern in memory. Three divided by eight is nought point three seven five. Five divided by sixteen is nought point three one two five, which is why five-sixteenths sits between a quarter and three-eighths and converts to just under eight millimetres. Notice the useful self-check hidden in the sixteenths: each sixteenth of an inch is nought point zero six two five, so you can build any sixteenth size by adding that step repeatedly, and any decimal that is not a multiple of that step is not a sixteenth size at all, however the chart row is labelled.
Work in one direction only during a job. Decide at the outset whether the project will be measured in inches or millimetres, translate every required size into that system using the chart, and write the translated list on tape stuck to the drill case. Mixing systems mid-job, converting one hole from a plan in inches and the next from a packet in millimetres, is how a correct chart produces an incorrect hole. The sheet is a translator that you consult once, carefully, at the planning moment, not a companion to be glanced at with the drill already spinning.
A Worked Lookup: Pilot and Clearance Holes for One Screw
Take a common task: joining two boards with a wood screw so the top board pulls down tightly onto the lower one. The cheat sheet serves this job twice, because the two boards need different holes. The lower board needs a pilot hole, sized so the screw threads bite into its fibres without splitting them. The upper board needs a clearance hole, sized so the screw shank passes through freely and the head does the clamping. Readers who look up only one size have done half the lookup, and the half they skipped explains the familiar failure where a joint will not close no matter how firmly the screw is driven: the threads are gripping both boards and holding them apart.
The lookup proceeds in a fixed order. First, identify the screw: its gauge or diameter and its length, from the packet. Second, find that screw in the chart’s pilot guidance for your material, noting that hardwood and softwood rows differ because dense fibres need a wider pilot to avoid splitting while soft fibres need a narrower one to keep their grip. Third, read across for the clearance size for the same screw. Fourth, check both chosen bits physically exist in your set, because numbered and letter sizes sometimes fill gaps between fraction sizes, and the chart may point you to a bit your set does not include.
Now apply the arithmetic self-check from the conversion section. If the pilot you selected is larger than the clearance size, something is wrong, since a clearance hole must pass the shank while a pilot must be narrower than the threaded portion. If the pilot equals the screw’s overall diameter, the threads will have nothing to bite. These two comparisons, larger-versus-smaller, catch most row-slipping errors without any specialist knowledge. Add a third check on length: the pilot depth in the lower board should suit the portion of the screw that will live there, and marking that depth on the bit with tape, as the depth guidance describes, turns a mental note into a physical stop.
Finish with the scrap test the sheet keeps recommending, and treat it as part of the lookup rather than an optional extra. Drill both holes in offcuts of the same material, drive the screw, and inspect: the top board should pull down with a clean closing of the joint, the lower board should show no bulge or split, and the screw should feel firm rather than spinning or straining. If any of those fail, move one size in the direction the failure indicates and test again. The chart got you to the right neighbourhood in one step; the test walks you to the right house.
Lookup Errors That Produce the Wrong Hole
The commonest error with a cheat sheet is reading the correct number from the wrong row, usually the row immediately above or below the intended one. It happens because the eye travels across a dense grid and drops a line, especially with similar fractions stacked together. The defence is physical: place a ruler or the edge of a card under the row you are reading, and read the size aloud with its unit. Speaking the unit matters. Many wrong holes have been drilled by someone who read a millimetre figure as if it were a decimal inch figure, and the numbers are close enough in size that the error is not obvious until the screw is offered up.
A second error is confusing the direction of numbered and letter gauges. In those systems, a larger number means a smaller bit, which reverses the instinct trained by fractions and millimetres where larger numbers mean larger sizes. A reader in a hurry can select a bit several sizes away from the target while feeling perfectly confident. The chart guards against this by listing equivalents side by side; use them. Whenever you pick a numbered or letter bit, read its fraction or millimetre equivalent from the same row and sanity-check that equivalent against the job. If the equivalent surprises you, stop and re-read before drilling.
A third error is treating a size printed on a worn bit case as truth. Stamps fade, bits get returned to the wrong slot, and sets accumulate stray bits from other sets over the years. The chart cannot fix a mislabelled case, but a ten-second check can: compare the bit against a neighbour of known size, or measure the shank with calipers if you have them, and confirm the bit is at least in the right order relative to the sizes either side of it in the case. Bits in a case should ascend smoothly in size along the row; any bit that breaks the visual progression deserves suspicion.
The fourth error is subtler: using the right size in the wrong material row. Pilot guidance differs between hardwood, softwood, sheet metal and masonry because the failure each hole must avoid differs: splitting, spinning, wandering or cracking. A size that performs beautifully in pine can split oak or skate across steel. When a job involves two materials, look up both rows and expect two answers. The extra minute is the entire point of keeping the sheet at the bench rather than memorising a single favourite size.
Checking a Bit Against the Sheet Before You Drill
Beyond reading the chart correctly, you can verify the physical bit in your hand with three quick checks that need no special equipment. The first is the neighbour check already described: hold the chosen bit between the next size up and the next size down from your set. It should sit visibly between them. If it matches one of its neighbours instead, the case slots or your selection are wrong. The second is the packet check: many screw packets print a recommended pilot size, and that figure should agree with the chart’s guidance for your material, or sit one step away for a defensible reason such as unusually hard or soft stock. A disagreement of several sizes means one source is being misread.
The third check uses the workpiece itself. Press the bit against the screw you intend to use and compare them directly, a method fitters have used for generations. For a pilot hole in wood, the bit should hide the screw’s core while leaving the threads standing proud on either side when you hold them together and sight across. For a clearance hole, the bit should match or just exceed the shank so the screw drops through without wobble. This visual comparison translates the chart’s numbers into the physical relationship the joint actually needs, and it catches unit errors instantly, because a bit chosen from the wrong column simply looks wrong against the screw.
Where calipers are available, they turn checking into measuring, but they need their own moment of care. Measure across the flutes of the bit at its widest point, not along the shank, since many bits have shanks narrower than their cutting diameter, and a shank measurement will reassure you wrongly. Compare the reading with the chart row you intended, allowing for the fact that inexpensive bits are not always ground to exemplary accuracy. A small deviation matters little for a pilot hole in softwood and more for a precise anchor hole in masonry, which is another way of saying the chart’s guidance and the job’s tolerance must be read together.
Make the checks a fixed part of the routine rather than a response to doubt. Doubt is unreliable; it stays silent on exactly the rushed, familiar jobs where errors breed. A routine that pairs every chart lookup with a neighbour check and a screw comparison takes under a minute, and it converts the cheat sheet from a reference you trust into a system you verify. That distinction is the whole craft of accurate drilling in miniature.
Keeping and Using the Sheet at the Bench
Where the sheet lives determines whether it gets used. A chart buried in a drawer or saved only on a phone with a flat battery loses to guesswork every time. Print it, protect it in a sleeve or laminate it if you can, and fix it where drilling decisions happen: inside the lid of the bit case is ideal, with the bench wall a close second. Beside it, keep a pencil. The sheet improves every time you annotate it with a result from your own materials: a note that a particular local hardwood needed the next pilot size up, or that a certain anchor in your house walls behaved better with a particular bit, is worth more than another decimal place of conversion precision.
Annotate failures as faithfully as successes. A short note recording the size that split a workpiece, with the material named, prevents a repeat performance a year later when the memory has faded but the chart remains. Over time these notes convert a generic published sheet into a personal record tuned to the timber, boards and walls you actually work with. That is the same process by which professional workshops develop their own charts, and it begins with a single honest annotation rather than any grand system.
Review the sheet itself occasionally for physical legibility. Workshop charts absorb dust, splashes and sunlight, and a faded row invites the misreading the sheet exists to prevent. Replace a tired printout before it becomes a hazard to accuracy. If you keep a second copy with your portable drill kit, update both copies when you annotate one, or accept that the travelling copy is for conversions only and the annotated master stays at the bench. Two disagreeing charts are worse than one, because every lookup acquires an unnecessary second question about which copy to believe.
Finally, teach the sheet to anyone who shares your tools. A partner, a teenager learning the drill, or a friend borrowing the set benefits from the same translation grid, and a household where everyone reads sizes the same way produces fewer mystery holes. Point out the three checks, especially the screw comparison, since a beginner can perform it with no instruments at all. The cheat sheet then becomes what the best workshop references always become: not a crutch for one person’s memory, but a shared standard for the whole bench.
More Questions Readers Ask About the Cheat Sheet
Why does the sheet list so many systems for the same sizes? Because the workshop inherits all of them at once. Plans arrive in fractions, packets in millimetres, older sets in numbers and letters, and none of those sources is willing to convert itself. The sheet exists so that you convert once, on paper, where a mistake is visible, rather than repeatedly in your head at the drill, where a mistake becomes a hole. Fluency comes with use; most regular users find the common sizes memorise themselves within a few projects, and the sheet remains for the uncommon ones.
What should I do when the exact size listed is missing from my set? Choose by the job the hole must do. For a pilot hole, a fractionally smaller bit in soft material or a fractionally larger one in hard, split-prone material is usually the safer neighbour, confirmed by the scrap test. For a clearance hole, err larger, since a slightly loose clearance costs nothing while a tight one defeats the joint. For anchors, follow the anchor maker’s stated size strictly and borrow, buy or hire the correct bit, because anchor performance depends on a hole the maker specified.
How do I stop confusing pilot and clearance when both are listed for one screw? Write the pair, not the single size, on your tape note: pilot first, clearance second, with the board each belongs to named beside it. Most confusion happens when a lone number travels from chart to drill without its role attached. A number with a job description survives the journey; a bare number becomes whatever the next board seems to need, which is how top boards end up with pilot holes and joints that will not close.
Is it worth learning the conversions rather than always using the sheet? Learn the anchors and keep the sheet. Knowing that a quarter inch is six point three five millimetres, that an eighth is about three point two, and that each sixteenth adds nought point zero six two five of an inch lets you estimate and error-check instantly, while the sheet still carries the full grid for sizes you meet rarely. Estimation plus verification is faster and safer than either memory or lookup alone.
Three Bench Exercises That Make the Sheet Second Nature
Fluency with sizes comes from handling them, and three short exercises build it faster than any amount of staring at the grid. The first is the sorting exercise: tip a mixed handful of bits onto the bench and arrange them in ascending order by eye, then check your order against the sheet and against each bit’s neighbours. Errors are instructive, because the sizes the eye confuses, the close pairs separated by a single step, are exactly the sizes to double-check during real lookups. Repeat the exercise whenever a new set arrives, since each set has its own close pairs and its own worn stamps.
The second exercise is the translation round. Take five sizes from recent packets, plans or instructions, in whatever system each arrives, and translate every one into the other two systems using the sheet, writing all three forms down. Then verify two of them by the multiplication method described earlier, and one by measuring the physical bit if calipers are available. The round takes minutes and rehearses the full loop of real use: read, translate, verify. Readers who do it monthly find that the common sizes stop needing the sheet at all, while the method for the uncommon ones stays sharp.
The third exercise is the failure review. Keep one split offcut, one stripped hole or one snapped screw from your own work, labelled with the size used and the size that should have been used, near the sheet. Physical evidence teaches what print cannot: the look of a pilot that was too small is remembered by the fingers as much as by the eye. A small museum of personal errors, honestly labelled, is a feature of many good workshops, and it converts the sheet from a reference into a record of your own calibration as a worker.
None of these exercises requires a project, which is their virtue. They can fill the ten minutes while adhesive cures or a battery charges, and they compound quietly. The sheet on the wall stays the authority, but the worker beside it becomes faster, more sceptical of worn stamps and misread rows, and quicker to run the physical checks that catch the errors print cannot prevent.
Sizes for the Jobs This Sheet Meets Most Often
Certain lookups recur so reliably that they deserve a rehearsal in the abstract, before the day they arrive under pressure. Fitting a screw into a stud through plasterboard, hanging a heavy frame on an anchor, drilling for a wall plug in masonry, and piloting hardwood for brass screws that snap if forced: each of these common jobs punishes the generic answer and rewards the chart’s specific row, read with its material column respected. The brass screw case is the one to internalise, because the failure is instant and the screw is ruined inside the work. Soft metals demand the generous pilot the chart’s guidance implies, driven by hand at the end, and no amount of care with a steel screw’s setting transfers safely to them.
Flat-pack and manufactured boards form the second family worth rehearsing. Their cores are softer and less fibrous than solid timber, so pilots behave differently, threads hold less, and overtightening destroys the material around the hole rather than the screw. The chart’s rows for manufactured material, where given, or a conservative scrap test where not, protect more furniture than any other single habit. When the board is faced or laminated, add the backing and tape defences from the drilling sections, since a perfect size in a chipped hole is still a failed job by the standards of the person who will look at it daily.
Rehearse these families once on scrap and the sheet’s abstract rows acquire faces. Thereafter the lookup under real pressure is a recognition rather than a research project, and recognition is faster and calmer in every workshop sense that matters.
FAQ
How do I know the right pilot size?
Hold the bit up against the screw. It should hide the inner core but leave the threads visible on both sides.
Why does my bit wander?
A dull tip, no guide dimple, or too much speed can cause it. Mark the spot and begin slowly.
Are metric and inch bits interchangeable?
Often close, but not identical. For a tight fit, use the system the part is made in, or check with a gauge.
Do I need a pilot hole in softwood?
Not always, but one helps near edges and ends, where wood is more likely to split. Try a test on scrap if you are unsure.
What does a numbered or lettered set mean?
These are older sizing systems that sit between standard fractions. Check the chart for the exact size each number or letter represents.
How deep should a pilot hole be?
A little deeper than the threaded part of the screw is a common aim, so the tip has room to move and dust can collect. Test on scrap with the actual screw. If the screw bottoms out, drill slightly deeper.
Can I use a countersink bit on any screw?
Only flat countersunk heads need the cone, and the cone should match the head width. Pan and round heads sit on the surface and need no cone. Check the screw packaging.
What is the easiest way to mark drilling depth?
A strip of masking tape wrapped around the bit works well. Stop drilling when the tape reaches the surface. A clamp-on depth collar does the same job with less fuss once set.
Why does the laminate chip on the back side?
The hard surface layer has little support as the bit exits. Clamp a backing board behind the work, start slowly and ease off as you break through.
Should I drill plastic at high speed?
No. Fast bits can melt plastic and cause rough holes. Use a sharp bit, a low speed and light pressure, and clear shavings often.
Is a drill stand worth having?
For repeatable, square holes, it can help, especially for dowels and small parts. It is optional for general home jobs. Consider how often you need precise vertical holes.
How do I know if my bit is running true?
Seat the bit fully, tighten the chuck, then spin the chuck by hand and watch the tip. A visible wobble suggests the bit is bent or not seated, so remove and refit it or replace it.
The Short Version
Match the bit to the material and the hole’s purpose: narrower for pilots, wider for clearance. Confirm sizes on the packaging, test on scrap and wear eye protection. Keep bits clean, sharp and organized.



